| 
Chapter 1717-59CONFIG Select several system software stored in the hard disk, change the nation/area, paper size.11) Select .2) Select the item to change.3) Press the +/- key. (Each press changes the setting.)4) Display the contents to be needed, press OK key.5) Turn off and then back on the main power switch.XXYYZZAAXX: country (e.g., JP=Japan)YY (*): language (e.g., ja=Japanese)ZZ: (*) destination (e.g., 00=Canon)AA: paper size series (00=AB; 01=inch; 02=A; 03=inch/AB)*: Cannot change the setting.TR-SP-C1 Use it to change the transfer/separation output settings for pickup from the right deck.1settingsMEMO:0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: Thick paper- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case ofthe setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding isprioritized over this service mode setting.TR-SP-C2 Use it to change the transfer/separation output setting for pickup from the left deck.1settings0: plain paper (defeat); 1: recycled paper; 2: tracing paper; 3: For thick paperMEMO:- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case ofthe setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding isprioritized over this service mode setting.TR-SP-C3 Use it to change the transfer/separation output setting for cassette 3.1settings0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: For thick paperMEMO:- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case ofthe setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding isprioritized over this service mode setting.TR-SP-C4 Use it to change the transfer/separation output setting for pickup from cassette 4.1settings0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: For thick paperMEMO:- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case ofthe setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding isprioritized over this service mode setting.TR-SP-MF Use it to change the transfer/separation output setting for pickup from the manual feeder tray.1settings0: plain paper (default); 1: recycled paper; 2: tracing paper; 3: For thick paperMEMO:- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case ofthe setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding isprioritized over this service mode setting.TR-SP-DK Use it to change the transfer/separation output setting for pickup from the side paper deck.1settings0: plain paper (default); 1: recycled paper; 2; tracing paper; 3: For thick paperMEMO:- In the case that the setting value is 0, control as for the paper that was set at the user mode or manual feeding.- In the case that the setting value is 1~3, control as for the recycled paper/tracing paper/thick paper. However, only in the case ofthe setting of tracing paper/tab paper at the user mode or manual feeding, the setting of the user mode and manual feeding isprioritized over this service mode setting.COPIER > OPTION > BODY*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).**: model equipped with DADF-M1 (outside Japan: iR7086).***: up graded versionSub item Description Level |
