Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Langer FLS 106 IC User Manual

Also see for FLS 106 IC: User manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Page 65 preview
Page 66 preview
Page 67 preview
Page 68 preview
Page 69 preview
Page 70 preview
Page 71 preview
Page 72 preview
Page 73 preview
Page 74 preview
Page 75 preview
Page 76 preview
Page 77 preview
Page 78 preview
Page 79 preview
Page 80 preview
Page 81 preview
Page 82 preview
Page 83 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Declaration of Conformity
  7. General Information
  8. Description of Symbols
  9. Scope of Delivery
  10. Technical Parameters
  11. Technical Parameters of the Subassemblies
  12. GND 25 Holder
  13. GND 25 Ground Plane
  14. SUH 106 Safety Enclosure
  15. Requirements for the ChipScan-Scanner Software
  16. Intended Use
  17. Risks if Not Used for Its Intended Purpose
  18. Hazard Due to Electrical Voltage
  19. Safety Devices
  20. Environmental Protection
  21. Overview of the FLS 106 Scanner
  22. Guide Rails along the Y-Axis (Long Side)
  23. Gantry
  24. Aluminium Mounting Bracket
  25. T-Slot Table
  26. Control Panel with EMERGENCY STOP Switch and Control LEDs
  27. ON / OFF Switch and Connectors
  28. Connectors on the Z-Axis Tower
  29. Overview of Attachments
  30. DM-CAM with Camera Screw
  31. Clamping Pieces
  33. SH 01 Probe Holder
  34. Delivery
  35. Opening the Transport Box
  36. Set-Up and Preparations for Putting the FLS 106 Scanner into Service
  37. Setting up the FLS 106
  38. Removing the Protective Film
  39. Removing the Transport Protection from the Guide Rails
  40. Checking / Releasing the EMERGENCY STOP Switch
  41. Putting the FLS 106 Scanner into Service for the First Time
  42. Installation
  43. Checking the Cables of the Rotary Unit
  44. Installing the DM-CAM Digital Microscope Camera
  45. Installing the DM-CAM Digital Microscope Camera on the FLS 106 PCB
  46. Connecting a Computer
  47. Switching the FLS 106 Scanner on
  48. Software Installation
  49. Installing the ChipScan-Scanner Software
  50. Putting the FLS 106 Scanner into Service with the ChipScan-Scanner Software
  51. Fastening the Device Under Test
  52. Fastening a Circuit Board on the UH DUT Universal Holder
  53. Fastening the Circuit Board
  54. Installing the GND 25 Ground Plane for IC Measurements
  55. Installing the GND 25 Ground Plane
  56. Installing an ICR Near-Field Microprobe
  57. Connecting the ICR Near-Field Microprobe
  58. Installing the BT 706 Bias-Tee
  59. Collision Control of the ICR Probe
  60. Installing a Near-Field Probe with the SH 01 Probe Holder
  61. Connecting a Near-Field Probe Directly to the FLS 106 IC Scanner
  62. Connecting a Near-Field Probe with a Preamplifier
  63. Installing a Near-Field Probe on the FLS 106 PCB
  64. Connecting a Near-Field Probe Directly to the FLS 106 PCB Scanner
  65. Collision Control for the Near-Field Probe
  66. Operational Notes
  67. Estimating the Duration of a Measurement with the FLS 106 Scanner
  68. Memory and Storage Requirements for the Measurement
  69. After Completing the Measurement
  70. Removing the Preamplifier / BT 706 Bias Tee
  71. Maintenance
  72. Dismantling
  73. Disposal
  74. Customer Service
  75. Warranty
Langer FLS 106 IC User Manual Manual pdf 28 page image
- 28 / 83 -LANGEREMV-TechnikDE-01728 Bannewitzmail@langer-emv.dewww.langer-emv.de FLS 106 IC set / FLS 106 PCB setON / OFF Switch and Connectors9.3ON / OFF Switch9.3.1Figure 20: ON / OFF switchAn ON / OFF toggle switch is located on the rear of the FLS 106 scanner.Power Supply Socket9.3.2Figure 21: Mains plug socket (power supply)A C14 power supply socket is located on the rear of the FLS 106 scanner to the right of theON / OFF switch.Connector for External Emergency Stop Switch or Safety Enclosure9.3.3Figure 22: ext. Stop connectorThe connector marked ext. Stop is located on the rear of the FLS 106 scanner and is used toconnect the SUH 106 safety enclosure or the external NA 5 EMERGENCY STOP switch.
/ 83
This manual is suitable for:
FLS 106 ICFLS 106 PCB
Manuals database logo
manualsdatabase
Your AI-powered manual search engine