manuals
database
Your AI-powered manual search engine
Search
Home
Brands
Magtrol
Controller
DSP7000
Magtrol DSP7000 User Manual
Print this manual
Download
Magtrol DSP7000 User Manual
Table of content
Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
introduCtion
DATA ShEET
Controls
Figure 2–2 Secondary Function Menu
VACUUM FLUoRESCENT DISPLAY (VFD)
Contrast Settings
REAR PANEL
Figure 2–7 TSC1/TSC2 Connector
Figure 2–10 I/O Interface Card 1 and Card 2
optional gPIb
installation/Configuration
Main Menu
Dynamometer Configuration Menu
hysteresis Dynamometer Setup
Figure 3–10 Hysteresis Dynamometer with Torque Transducer Setup
hysteresis Dynamometer with Eddy-Current or Powder brake Setup
Eddy-Current or Powder brake Dynamometer Setup
Figure 3–16 TSC1 Eddy-Current Setup Menu
Eddy-Current or Powder brake Dynamometer with Torque Transducer Setup
Two Eddy-Current/Powder brake Dynamometers (Independent Setup)
Two Eddy-Current/Powder brake Dynamometers (Tandem Setup)
Eddy-Current Dynamometer with Powder brake Dynamometer (Tandem Setup)
In-Line Torque Transducer with brake
ToRqUE FILTER SETUP
Figure 3–27 RPM vs PPR Chart
TACh A
CoNFIgURE CoMMUNICATIoN
pid settings
SETTINg ThE CoRRECT PID'S FoR YoUR MoToR
Figure 4–3 High Initial P Setting for Torque Control
Figure 4–4 Initial I Setting for Torque Control
Figure 4–7 Initial I Setting for Speed Control
Figure 4–9 Ramp Down Low I
Figure 4–10 Ramp Down High I
alar m system
Figure 5–3 Typical Application
PoWER ALARM
Instructions for Power Alarm Setup
Instructions for global Power Alarm Setup
Instructions for Maximum Speed Alarm Setup
Instructions for Maximum Torque Alarm Setup
gLobAL ToRqUE ALARM
Instructions for Air Flow Alarm Setup
WATER FLoW ALARM
ExTERNAL ALARM (I/o CARD oPTIoN)
TEMPERATURE ALARM (Wb/Pb oNLY)
CLUTCh ALARM (Wb/Pb oNLY)
manually Controlled operation
hoW To SET ToRqUE CoNTRoL
hoW To SET SPEED CoNTRoL
hoW To SET oPEN LooP CoNTRoL
hoW To SET AND RESET TARE FUNCTIoN
hoW To SET ThE TM/TF INVERT FLAg
Computer Controlled operation
DATA FoRMAT
PRogRAMMINg
Timeout
Communication Commands
Torque Commands
Miscellaneous Commands
quadrature Commands
MoDE
optional equipment
I/o Card Installation
I/o Card Interface
Figure 8–4 Filter Channel Setup Menu
Figure 8–7 Alarm Contact Setup
gPIb INTERFACE
Figure 8–10 GPIB Card Installation
Figure 8–11 GPIB Installation
RS232 INTERFACE
Connection
baud Rate
Figure 8–18 Connected Instruments Window
Figure 8–20 Query Window
Figure 8–22 Tera Term Licence Agreement Window
Figure 8–24 Tera Term Select Components Window
Figure 8–26 Tera Term Start Menu Folder Window
Figure 8–28 Tera Term Window
Figure 8–30 Serial Port Setup Window
Calibration
theory
Equations
FILTER PARAMETERS
troubleshooting
appendix a: inertia CorreCtion
appendix b: front panel/display menu flow Charts
b.2 SECoNDARY kEY FUNCTIoNS
b.2.5 Max Speed
b.3 TEST INSTRUMENT SETUP
appendix C: sChematiCs
C.2 DSP7000 ANALog INPUTS
C.3 DSP7000 DIgITAL INPUTS
C.4 DSP7000 ENCoDER IN
C.5 DSP7000 ANALog oUTPUT
C.6 DSP7000 DIgITAL oUTPUT
appendix d: additional sCale faCtor table
serviCe information
125
Magtrol Model DSP7000 Dynamometer Controller
A
p
p
e
n
d
ix B: FrontPanel/Display Menu Flow Charts
APPENDICES
B.2.4
T
orque
u
ni
TS
TORQUE
UNITS
SHIFT
N.m
cN.m
mN.m
kg.cm
g.cm
lb.ft.
lb.in.
oz.ft.
oz.in.
B.2.5
M
ax
S
pee
D
MAX
SPEED
SHIFT
0.000–99,999
Previous
Next
/ 160
Zoom view
Related manuals for Magtrol DSP7000
Magtrol DSP6000 User Manual
Magtrol DSP6001 User Manual
Magtrol 6200 User Manual
Magtrol AN Series Instruction Manual
This manual is suitable for:
DSP7000
manuals
database
Your AI-powered manual search engine
