–158–Chapter 7 Display—Screen status displayf[CLIP&T&=] ([CLIP&T~&]): Cueing up (rewinding) by clip and text memo (when [CLIP&TEXT MEMO] is set in the main menu→[OTHERFUNCTIONS]→[SEEK POS SEL])f[START]*1: Displayed when recording of a new clip is started in one-clip recording.f[END]*1: Displayed when combining of clips is ended in one-clip recording.f[L-]*2: Loop recordingf[I-]*2: Interval recording, one-shot recordingf[P-]*2: Pre-recording*1If the display is set to [OFF], only [REC], [START], and [END] are displayed. Also, when pre-recording, loop recording, interval recording, or one-shotrecording is set, it is displayed.*2Displayed when [INTERVAL], [ONE SHOT], or [LOOP] is set in the main menu→[RECORDING SETUP]→[RECORDING], or when [ON] is set in themain menu→[RECORDING SETUP]→[PRE REC].43 switch operation displayDisplayed when the switch is set to .44Rec during upload function status displayDisplays the status of rec during upload.f[]: Displayed when the rec during upload function is enabled.The display will blink when recording is started immediately after the power is turned on or the P2 card is inserted, and the upload will not beexecuted until the recording is stopped.f[]: Displayed during upload.f[]: Displayed from when transfer error occurred during upload until when the next upload starts.45GPS displayDisplays the strength of the GPS signal reception in four levels. The GPS signal strength is indicated by the number of vertical bars. It is notdisplayed when GPS is disabled.46Streaming distribution status displayDisplays the streaming status.f[] (flashing): Flashes while the camera is being connected to a device which will receive the streaming video.f[] (illuminated): Displayed when the camera is connected to a device receiving the streaming video and the camera is transmitting streamingvideo.The display turns off when a connection could not be established properly.@@NOTEtDepending on the network status, the [] display may not be able to follow during actual operation.47HD SDI REMOTE recording status and 4G/LTE connection statusDisplays the control status of whether recording has started or stopped for an external device which is connected to the terminal.When the main menu→[OUTPUT SEL]→[HD SDI REMOTE] is set to [ON], it will always be displayed regardless of the settings in the main menu→[DISPLAY SETUP]. It is not displayed when [HDSDI REMOTE] is set to [OFF].f[SDIn]: Status where the recording is being instructed for an external devicef[SDI&]: Status where recording stop is being instructed for an external deviceDisplays the 4G/LTE connection status. Displays at the 4G/LTE connection. Displays the strength of the signal reception in six levels. Displays theradio wave strength with the number of vertical bars. It is not displayed when the setting of 4G/LTE is disabled.f[4G/LTE]: During 4G/LTE connectionf[4G/LTE]: When not connected with 4G/LTEf[4G/LTE]: When there is a problem with the 4G/LTE connection@@NOTEtDepending on the USB modem that is supported, vertical bars that indicate the signal strength may not be displayed.48Audio monitor volume adjustment displayDisplayed when the after the operation.49Front audio level volume displayThe volume is displayed for three seconds when it is adjusted with the dial.Camera status displayThese are indicated in the information display area in the center.[ABB]: Displayed while automatic black balance operation is active.[ATW ACTIVE]: Displayed when the button is pressed while auto tracking white balance is active.[ATW]/[ATW LOCK]: Displayed when the switch is turned to if [ATW] is allocated.[AWB]: Displayed while automatic white balance operation is active.[AWB P3200K]/[AWB P5600K]: When the switch is at position, displays the color temperature assigned to . It is alsodisplayed when you attempt to perform automatic white balance with the switch at position.[BACK LIGHT]: Displayed when pressing the USER button to which [BACK LIGHT] is allocated for iris control and switching the status.[GAIN**dB]: Displayed when gain is switched.[IRIS:MANUAL]/[IRIS:AUTO]: Displayed when you switch the iris operation.[SHUTTER 1/****]/[SHUTTER OFF]: Displayed when you switch the shutter speed.[SPOT LIGHT]: Displayed when pressing the USER button to which [SPOT LIGHT] is allocated for iris control, and switching the status.
