Panasonic AJ-PX270 Operating Instructions Manual

Also see for AJ-PX270: Settings guide Quick guide Specifications Operating instructions Operating instructions

Contents

– 203 –Chapter 10 Maintenance and Inspection — Warning systemWarning systemIf an error is detected immediately after the camera is turned on or during operation, the viewfinder, LCD monitor, and tally lamp indicate the error. Dealwith the error by following the indications.Cases indicated by error codesError code Display Description Behavior and cause[E-30] [TURN POWER OFF][P2 CARD]An error occurred in the camera built-in memorybecause the P2 card being accessed was ejected.f Tally lamp flashes four times per second.f Cannot operate.f Follow the message to turn off the power once andturn on the power again.f Ensure that there is no error in the clips on the ejectedcard, and restore the clips as necessary.[E-31] [TURN POWER OFF][SYSTEM MODE]System mode error occurred.f Tally lamp flashes four times per second.f Cannot operate.f Follow the message to turn off the power once, turnon the power again, and check that there is no errordisplay.[E-33] [SYSTEM ERROR][CAMERA]Camera unit error occurred.f Tally lamp flashes four times per second.f The operation stops.f Contact your dealer.[E-35] [SYSTEM ERROR][CODEC]Codec control error occurred.f Tally lamp flashes four times per second.f The operation stops.f Contact your dealer.[E-36] [SYSTEM ERROR][P2 SYSTEM]P2 system error occurred.f Tally lamp flashes four times per second.f The operation stops.f Contact your dealer.[E-37] [SYSTEM ERROR][P2CS]P2CS microcomputer error occurred.f Tally lamp flashes four times per second.f The operation stops.f Contact your dealer.[E-39] [SYSTEM ERROR][INITIALIZE]Video initialization error occurred.f Tally lamp flashes four times per second.f The operation stops.f Contact your dealer.[E-64][SYSTEM ERROR][FRAME SIGNAL](or no display)Reference signal error occurred.f Tally lamp flashes four times per second.f The operation stops.f Contact your dealer.Cases indicated by error messagesDuring recording/playbackDisplay Description Behavior and cause[AUTH NG CARD] (slot number)CPS authentication of microP2 memory card has failed.The microP2 memory card whose CPS authenticationfailed cannot be recorded or played back.f The current operation will continue.f Select [AUTHENTICATE] in the main menu → [CLIP],and enter the password.[BACKUP BATT EMPTY]Displays any reduced voltage detected on the backupbattery in the internal clock when the power is turnedon.f The current operation will continue.f Charge the built-in battery.[SET DATE AND TIME] Displayed when the internal clock setting is reset. f The current operation will continue.f Set the date/time of the internal clock. (page 33)[CARD ERROR] (slot number)Displayed when an data error caused by the P2 cardoccurs during recording.Displayed after recording stops until the next operation.Also displayed for three seconds during playback whena P2 card error causes playback to stop.f If the error occurs during recording, the tally lampflashes four times per second for approx. threeseconds after recording stops.f The tally lamp does not flash when an error occursduring playback.f The operation will stop.f After it stops, the P2 card on which the error occurredis write-protected. Replace the P2 card of the slotwhere the error occurred.[DIR NG CARD] (slot number) The directory position is not correct.f The current operation will continue.f Make a card backup immediately and format the cardto use it again.[FAN STOPPED] Displayed when the fan motor stops.f The current operation will continue.f If the fan has stopped with error, stop using thecamera immediately and consult your dealer.f If the fan has stopped, temperature of the camerawill rise. Therefore, do not use the camera for a longperiod of time.[HIGH TEMPERATURE] The temperature inside the camera is higher than that ofthe normal conditions.f The current operation will continue.f Turn off the power of the camera, turn it on again,and check recording and playback operations. If theproblem persists, consult your dealer.[PB INTERMITTENT] (slot number)Playback is interrupted on the SDHC/SDXC memorycard. A card whose playback performance cannot beassured is inserted.f The current operation will continue.f Use of microP2 or P2 memory card is recommended.