No.(Addr.Hex) Name LCD Display Description Values Pageo2-04(0508) Drive Model Selection Inverter Model # Enter the drive model. Setting required only if installing a newcontrol board. Default:Determined bydrive capacity –o2-05(0509)Frequency ReferenceSetting MethodSelectionOper Ref Method0: Disabled1: Enabled0: ENTER key must be pressed to enter a frequency reference.1: ENTER key is not required. The frequency reference can beadjusted using the up and down arrow keys only.Default: 0Range: 0, 1 –o2-06(050A)Operation Selectionwhen Digital Operator isDisconnectedOper Discon Det0: Disabled1: Enabled0: The drive continues operating if the digital operator isdisconnected.1: An oPr fault is triggered and the motor coasts to stop.Default: 1Range: 0, 1 –o2-07(0527)Motor Direction atPower Up when UsingOperatorFor/RevSel@PwrUp0: Forward1: Reverse0: Forward1: ReverseThis parameter requires assigning drive operation to the digitaloperator.Default: 0Range: 0, 1 –o2-09(050D) – – Factory use. – –o2-19(061F)<1>Selection of ParameterWrite during UvParameterSet Sel0: Disabled1: EnabledSelects whether parameter settings can be changed during a DCbus undervoltage condition. To be used with 24 V PowerSupply option (PS-A10L, PS-A10H) revision B or later.0: Disabled1: EnabledNote: Enabling this function may trigger a CPF06 faultwhen used with a 24 V Power Supply optionrevision earlier than B, as the parameter changesmight not occur correctly.Default: 0Range: 0, 1 –<1> Available in drive software versions PRG: 1019 and later.u o3: Copy FunctionNo.(Addr.Hex) Name LCD Display Description Values Pageo3-01(0515) Copy Function SelectionCOPY SELECT0: COPY SELECT1: INV→OP READ2: OP→INV WRITE3: OP←→INVVERIFY0: Copy select1: INV → OP READ (Read parameters from the drive, savingthem onto the digital operator).2: OP → INV WRITE (Copy parameters from the digitaloperator, writing them to the drive).3: OP → INV VERIFY (Verify that parameter settings matchthe data saved on the operator).To read the drive parameter settings into the digital operator,set o3-02 to 1 (to allow reading).Default: 0Range: 0 to 3 –o3-02(0516) Copy Allowed Selection Read Allowable0: Disabled1: EnabledSelects whether the read operation (o3-01 = 1) is enabled ordisabled.0: Read operation prohibited1: Read operation allowedDefault: 0Range: 0, 1 –u o4: Maintenance Monitor SettingsNo.(Addr.Hex) Name LCD Display Description Values Pageo4-01(050B) Cumulative OperationTime Setting DrvElapsTimeCnt Sets the value for the cumulative operation time of the drive inunits of 10 h. Default: 0Min.: 0Max.: 9999 –o4-02(050C) Cumulative OperationTime SelectionElapsTimeCntSet0: Power-On Time1: Running Time0: Logs power-on time1: Logs operation time when the drive output is active (outputoperation time).Default: 0Range: 0, 1 –o4-03(050E) Cooling Fan OperationTime Setting FanElapsTimeCn Sets the value of the fan operation time monitor U4-03 in unitsof 10 h. Default: 0Min.: 0Max.: 9999 –o4-05(051D) Capacitor MaintenanceSetting BusCap Maint SetSets the point at which the cumulative timing for the maincircuit capacitor maintenance starts.View monitor U4-05 to determine when the capacitors mayrequire replacement.Default: 0%Min.: 0Max.: 150 –B.10 o: Operator-Related SettingsYASKAWA ELECTRIC TOEP C710616 41G YASKAWA AC Drive - A1000 Quick Start Guide 313B Parameter List
