Drive ModelWire Gauge (AWG, kcmil)ScrewSizeCrimpTerminalModelNumberToolInsulationCap ModelNo. Code <1>R/L1, S/L2, T/L3 U/T1, V/T2, W/T3 Machine No. Die Jaw4A04144/0 × 2PM12100-L12YF-1YET-300-1TD-324,TD-312 TP-100 100-051-560250 × 2P 150-L12 TD-325,TD-313 TP-150 100-051-562300 × 2P4A05153/0 × 4P 3/0 × 4PM1280-L12YF-1YET-300-1TD-323,TD-312 TP-080 100-051-5584/0 × 4P 4/0 × 4P 100-L12 TD-324,TD-312 TP-100 100-051-560250 × 4P 150-L12 TD-325,TD-313 TP-150 100-051-562300 × 2P4A06754/0 × 4PM12100-L12YF-1YET-300-1TD-324,TD-312 TP-100 100-051-560250 × 4P 150-L12 TD-325,TD-313 TP-150 100-051-562300 × 4P4A09303/0 × 8PM1280-L12YF-1YET-300-1TD-323,TD-312 TP-080 100-051-5584/0 × 8P 100-L12 TD-324,TD-312 TP-100 100-051-560250 × 8P 150-L12 TD-325,TD-313 TP-150 100-051-562300 × 8P4A12004/0 × 8PM12100-L12YF-1YET-300-1TD-324,TD-312 TP-100 100-051-560250 × 8P 150-L12 TD-325,TD-313 TP-150 100-051-562300 × 8P<1> Codes refer to a set of three crimp terminals and three insulation caps. Prepare input and output wiring using two sets for each connection.Example 1: Models with 300 kcmil for both input and output require one set for input terminals and one set for output terminals, so the user shouldorder two sets of [100-051-272].Example 2: Models with 4/0 AWG × 2P for both input and output require two sets for input terminals and two sets for output terminals, so the usershould order four sets of [100-051-560].Note: Use crimp insulated terminals or insulated shrink tubing for wiring connections. Wires should have a continuous maximum allowabletemperature of 75 °C 600 Vac UL-approved vinyl-sheathed insulation.Factory Recommended Branch Circuit Protection for UL ComplianceNOTICE: If a fuse is blown or a Ground Fault Circuit Interrupter (GFCI) is tripped, check the wiring and the selection of the peripheral devicesto identify the cause. Contact Yaskawa before restarting the drive or the peripheral devices if the cause cannot be identified.Yaskawa recommends installing one of the following types of branch circuit protection to maintain compliance with UL508C.Semiconductor protective type fuses are preferred. Alternate branch circuit protection devices are also listed in the tablesbelow.Table C.7 Factory Recommended Drive Branch Circuit Protection (Normal Duty)Drive ModelNormal DutyNominalOutput PowerHPAC Drive InputAmpsMCCB RatingAmps<1>Time Delay FuseRating Amps <2>Non-time DelayFuse RatingAmps <3>Bussmann Semi-conductor FuseRating (FuseAmpere) <4>200 V Class2A0004 0.75 3.9 15 6.25 10 FWH-70B (70)2A0006 1 - 1.5 7.3 15 12 20 FWH-70B (70)2A0008 2 8.8 15 15 25 FWH-70B (70)2A0010 3 10.8 20 17.5 30 FWH-70B (70)2A0012 3 13.9 25 20 40 FWH-70B (70)2A0018 5 18.5 35 30 50 FWH-90B (90)2A0021 7.5 24 45 40 70 FWH-90B (90)2A0030 10 37 60 60 110 FWH-100B (100)C.2 UL and CSA Standards344 YASKAWA ELECTRIC TOEP C710616 41G YASKAWA AC Drive - A1000 Quick Start Guide
