Chapter 1616-41DFDST-L1 Use it to adjust the dust detection level for the ADF (sheet-to-sheetcorrection).A higher setting will cause the machine to be more sensitive to finer particlesof dust.setting: 0 to 225(Setting the item to '0' will disable the dust detection mechanism.)1DFDST-L2 Use it to add the dust detection level for the ADF (post-job detection).A higher setting will cause the machine to detect finer particles of dust.setting: 0 to 255(Setting the item to '0' will disable the dust detection mechanism.)1ENVP-INT Use it to set the interval at which a log is collected for the machine insidetemperature/humidity and fixing temperature.COPIER>FUNCTION>MIS-P>ENV-PRT andCOPIER>DISPLAY>ENVRNTsetting0 to 480 (default: 60; in min)1BASE-SW Use it to switch from MEAP-full model to base model.setting0: off (based model)1: on (full model)1SC-L-CNT Use it to change the threshold level of the paper size (large/small) for the scancounter.setting0: count B4 as small size (default)1: count B4 as large size1DHON-TM Use it to set the timing at which drum heater goes on in sleep mode (withreference to clock time).setting: 0 to 24 (default: 0: in hr)1DHON-IVL Use it to set the timing at which the drum heater goes on in sleep mode (withreference to time after a shift to sleep mode).setting: 0, 15 to 1440 (default: 0; in min)1DHOF-TM Use it to set the timing at which the drum heater goes off in sleep mode (withreference to clock time).setting: 0 to 24 (default: 01; in hr)1DHOF-IVL Use it to set the timing at which the drum heater goes off in sleep mode (withreference to clock time).setting: 0, 15 to 1440 (default: 0; in min)1CBLTINVL Use it to change the number of times the fixing web solenoid goes on.Make use of it when image faults occur as the result of soiling on the pressureroller.Setting0: normal (default)1: twice normal1PO-CNTMD Use it to select the number of times the potential control mechanism goes on.0: once at power-on1: once at power-on and, in addition, 10 and 60 min thereafter (simplifiedpotential control mode)2: once at power-on and, in addition, 10 and 60 min thereafter (normalpotential control mode; default)2W-CLN-P Use it to set the interval at which the primary charging wire is automaticallycleaned.setting: every 100 to 2000 (sheets; default at 2000)2IDL-MODE Use it to select idle rotation mode for the developing assembly.0: fix to low humidity mode (off)1: environment control (default)2: fix to normal temperature/humidity mode (idle rotation for 120 sec)3: fix to high humidity mode (idle rotation for 300 sec)4: power save mode2FSPD-S1 Use it to select fixing enhancement mode.0: normal (default)1: fixing enhancement mode2: not used2TSPLY-SW Use it to switch over toner supply sequence.0: environment control (default)1: fix to low humidity mode (on for 1.4 sec, off for 1 sec)2: fix to normal temperature/humidity mode (on for 1.5 sec, off for 1 sec)3: fix to high humidity mode (on for 3 sec, off for 2 sec)2SCANSLCT Use it to enable/disable the function used to compute the scan area from theselected paper size.setting0: off (determine scan area by original detection)1: on (determine scan area by paper size)2OHP-TEMP Use it to switch over control temperature for transparency mode.setting0: normal (default); 1: -5 deg C; 2: -10 deg C; 3: -15 deg C; 4: -20 deg C2COPIER > OPTION > BODYSub-item Description Level
