Chapter 77-111F-7-2627.14.41 Patch Image Sensor7.14.41.1 Preparation for Removing the Patch ImageSensor Unit 0013-9759imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Open the front cover.2) Detach the process unit cover.3) Lift the hopper unit.4) Remove the primary charging assembly. (page 7-86)Reference [Re-moving the Primary Corona Assembly]5) Remove the pre-transfer charging assembly. (page 7-88)Reference [Re-moving the pre-transfer corona assembly]6) Remove the drum unit. (page 7-89)Reference [Removing the DrumUnit]7.14.41.2 Removing the Patch Image Sensor Unit 0013-9760imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Remove the patch image sensor unit [1].- 1 connector [2]- 2 screws [3]F-7-2637.14.41.3 After Replacing the Patch Image ReadingSensor 0014-3695imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+Run the following items in the Service Mode after replacing the patch imagescan sensor.Service Mode (Patch Detection Sensor Default Correction) :COPIER > ADJUST > DENS > ALF-F (front)>COPIER > ADJUST > DENS > ALF-C er)>This sensor unit comes with the following correction value labels (3 in total).The labels contain correction values for each sensor (front, center and rear).Enter the label values (4 digits) [1] using the above service mode.After entering the values, put the labels onto the new sensor unit.F-7-2647.14.42 Charging Wire7.14.42.1 Preparation for Setting Up Charging Wire 0014-0978imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Open the front cover.2) Detach the process unit cover.3) Lift the hopper unit.4) Remove the primary charging assembly. (page 7-86)Reference [Re-moving the Primary Corona Assembly]5) Remove the primary grit plate. (page 7-87)Reference [Removing thePrimary Grid Plate]6) Remove the primary charging assembly pad folder. (page 7-87)Refer-ence [Removing the Primary Corona Assembly Pad Holder]7) Remove the primary charging assembly slider. (page 7-88)Reference[Removing the Primary Corona Assembly Slider]7.14.42.2 Setting Up Charging Wire 0013-9738imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+The following procedure is basically the common procedure among allcharging assemblies. The primary charging assembly is used here as an ex-ample.1) Remove the shield plate [1].- 2 screws [2]- 1 holder [3]F-7-2652) Remove the wire cleaner.3) Loosen the charging wire [2] about 5 cm from the charging wire reel [1]of wire diameter 0.06 mm, and make a loop of diameter 2 mm on the edge.MEMO:When making a loop, roll the charging wire in the hex key once, and roll thehex key three to four times to twist the charging wire. By doing so, you caneasily make a loop.4) Cut the edge of the twisted charging wire (excess wire) using a wire cutter.5) Hook the loop on the stud [3].F-7-2666) Hook the charging wire [2] on the charging wire positioning [1] at rearside, and then, hook the charging wire tension spring [3] to the chargingwire at the position indicated below and twist it.[1][2][3][1][2][3][3][1][1] [2][2] [3][1][2][3](FRONT) (REAR)
