Chapter 1414-41FU7-0381 23T/50T GearFM2-2485 Secondary Transfer Mount Assembly14.3.7.13 E198-1000: J3502 connector on Color Sensor Driver PCB has poor contact 0016-2920imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1+ (Printer) / imagePRESS C1+[ Case in the field ]DescriptionSince Pin7 of J3502 connector on the Color Sensor Driver PCB became loose, the connector had poor contact, ultimately causing the error code "E198-1000."- E198-1000 can be displayed when a communication error occurs between the Color Sensor Driver PCB and the DC Controller PCB.- The Color Sensor Driver PCB is used to detect the density of patch on image.Field Remedy1. Gently pull each wire of J3502 connector cable on the Color Sensor Driver PCB to check if there is a pin that becomes loose; if any, go to Step 2. If not,go to Step 3.2. Bring up the claw of the loosen pin slightly, and insert it to the connector; then check to make sure that the pin does not come off the connector.3. Gently pull each wire of J1182 connector cable on the DC Controller PCB to check if there is a pin that becomes loose; if any, go to Step 4. If not, go toStep 5.4. Bring up the claw of the loosen pin slightly, and insert it to the connector; then check to make sure that the pin does not come off the connector.5. If the symptom still occurs after Step 1 or Step 3, check the drawer connector cable of the fixing feeder assembly in the same manner as described above.If a fault is found, modify it.FM2-7733 Color Sensor Driver PCB Assembly14.3.7.14 E202-0001/E202-0002/ Document exposure lamp's failure to light up occurs when mounting DADF-R1 0018-6306imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+[ Case in the field ]DescriptionAfter mounting the DADF-R1, either of the following symptoms occurred: document exposure lamp's failure in lighting up, E202-0001, or E202-0002.- E202-0001 can be displayed when an error is found during the forward trip of the HP search. The possible cause of this error is a fault in the scanner motoror the reader controller PCB.- E202-0002 can be displayed when an error is found during the return trip of the HP search. The possible cause of this error is a fault in the scanner HPsensor, scanner motor, or reader controller PCB.CauseSince the fan harness was pinched when mounting the cooling fan, the fuse on the interface PCB had an open-circuit.Field Remedy1. When the same symptom occurred after mounting the DADF-R1, check if the harness of the cooling is pinched.2. If the cooling fan harness is pinched, suspect removal of harness covering and replace the fan and interface PCB with new ones (because the fuse may havehad an open-circuit).FL2-3427 Front FanFL2-3426 Rear FanFM2-4662 Interface PCB Assembly14.3.7.15 E225-0001 occurs with machine in which R-CON software Ver. 1.27 is installed 0018-6304imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+[ Inspected by Canon Inc. ]DescriptionA machine in which R-CON software Ver. 1.27 was installed sometimes caused the error code "E225-0001."- E225-0001 can be displayed when the shading level is lower than the specified due to blowout of the lamp.CauseThere was a difference in timing between the CCD output and detection.Field Remedy1. Check the version of the R-CON software; if it is earlier than Ver.4.02, upgrade the software to ver. 4.02 or later.2. If the version of the software is earlier than Ver. 4.02, refit the flexible cable connecting the Reader Controller PCB to the Inverter PCB. Or clean theterminals of the cable with lint-free paper moistened with alcohol, and then refit the terminals. Also, check the connection of the scanner lamp (Xenon lamp)connector.3. If the symptom still occurs, replace the CCD with a new one.FM2-3920 CCD Unit14.3.7.16 E604-1536 is displayed when connecting Secure Watermark-A1: This machine does not have sufficient imagememory 0017-6706imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1 (CUSTOM) / imagePRESS C1+ (Printer) / imagePRESS C1+[ Case in the field ]DescriptionSince the error code "E604-1536" was displayed upon installation due to insufficient image memory, an image memory (option) was connected for solution.- E604-1536 can be displayed when the image memory is faulty or lacking.Field RemedyWhen connecting the Secure Watermark-A1, Security Expansion Board-E1, and imageRUNNER Security Kit-A2, a memory of 512MB is required. Whenconnecting these items, connect an option memory (512MB DDR-SDRAM) to the connector at J1001 on the Main Controller PCB.Note: If the Security Expansion Board-E1 or the imageRUNNER Security Kit-A2 is used together with the Color UFRII/PCL/PS Printer Kit-P1, it is notnecessary to connect the option memory. This is because it comes standard with the Color UFRII/PCL/PS Printer Kit-P1.0529B002 imageRUNNER512MB Expansion RAM-C1 (Product)14.3.7.17 E677-0080: Communication error occurs between this machine and imagePRESS Server- Q1 0015-8160imagePRESS C1 P / imagePRESS C1 / Color Image Reader-H1 / imagePRESS C1+ (Printer) / imagePRESS C1+[ Case in the field ]DescriptionSince the error code "E677-0080" was indicated, the Reset key on the front side of the imagePRESS Server-Q1 was pressed to correct the error. In case thatthe same symptom occurs, perform the following field remedy before pressing this Reset key.- E667-0080 can be displayed when there is an error in the communication with the printer after the external controller has started up normally.
