Danfoss VLT AQUA Drive FC 202 Programming Manual

Also see for VLT AQUA Drive FC 202: Service guide Installation guide Installation guide Operating guide Installation guide

Contents

Function at Stop [RPM]. The motor isrunning and there are no warnings.[8] Run onreference/nowarningMotor runs at reference speed.[9] Alarm An alarm activates the output. There areno warnings.[10] Alarm orwarningAn alarm or a warning activates theoutput.[11] At torque limit The torque limit set inparameter 4-16 Torque Limit Motor Modehas been exceeded.[12] Out of currentrangeThe motor current is outside the range setin parameter 4-18 Current Limit.[13] Below current,lowMotor current is lower than the setting inparameter 4-50 Warning Current Low.[14] Above current,highMotor current is higher than the setting inparameter 4-51 Warning Current High.[15] Out of speedrangeOutput speed is outside the ranges set inparameter 4-52 Warning Speed Low andparameter 4-53 Warning Speed High.[16] Below speed,lowOutput speed is lower than the setting inparameter 4-52 Warning Speed Low.[17] Above speed,highOutput speed is higher than the setting inparameter 4-53 Warning Speed High.[18] Out offeedbackrangeFeedback is outside the ranges set inparameter 4-56 Warning Feedback Low andparameter 4-57 Warning Feedback High.[19] Belowfeedback lowFeedback is below the limit set inparameter 4-52 Warning Speed Low.[20] Abovefeedback highThe feedback is above the limit set inparameter 4-56 Warning Feedback Low.[21] ThermalwarningThe thermal warning turns on when thetemperature exceeds the limit in themotor, the frequency converter, the brakeresistor, or the thermistor.[25] Reverse Reversing. Logic 1 = relay activated, 24 VDC when clockwise rotation of the motor.Logic 0 = relay not activated, no signal,when counterclockwise rotation of themotor.[26] Bus OK Active communication (no timeout) via theserial communication port.[27] Torque limitand stopUsed in performing a coast stop and intorque limit condition. If the frequencyconverter has received a stop signal and isat the torque limit, the signal is logic 0.[28] Brake, nowarningThe brake is active and there are nowarnings.[29] Brake ready,no faultThe brake is ready for operation and thereare no faults.[30] Brake fault(IGBT)The output is logic 1 when the brake IGBTis short-circuited. Use this function toprotect the frequency converter if there isa fault on the brake modules. Use theoutput/relay to cut out the mains voltagefrom the frequency converter.[35] ExternalInterlockExternal interlock function has beenactivated via 1 of the digital inputs.[40] Out of refrange[41] Belowreference low[42] Abovereference high[45] Bus Ctrl[46] Bus Ctrl 1 iftimeout[47] Bus Ctrl 0 iftimeout[55] Pulse output[60] Comparator 0 See parameter group 13-1* Comparators. Ifcomparator 0 is evaluated as true, theoutput goes high. Otherwise, it is low.[61] Comparator 1 See parameter group 13-1* Comparators. Ifcomparator 1 is evaluated as true, theoutput goes high. Otherwise, it is low.[62] Comparator 2 See parameter group 13-1* Comparators. Ifcomparator 2 is evaluated as true, theoutput goes high. Otherwise, it is low.[63] Comparator 3 See parameter group 13-1* Comparators. Ifcomparator 3 is evaluated as true, theoutput goes high. Otherwise, it is low.[64] Comparator 4 See parameter group 13-1* Comparators. Ifcomparator 4 is evaluated as true, theoutput goes high. Otherwise, it is low.[65] Comparator 5 See parameter group 13-1* Comparators. Ifcomparator 5 is evaluated as true, theoutput goes high. Otherwise, it is low.[70] Logic Rule 0 See parameter group 13-4* Logic Rules. Iflogic rule 0 is evaluated as true, theoutput goes high. Otherwise, it is low.[71] Logic Rule 1 See parameter group 13-4* Logic Rules. Iflogic rule 1 is evaluated as true, theoutput goes high. Otherwise, it is low.[72] Logic Rule 2 See parameter group 13-4* Logic Rules. Iflogic rule 2 is evaluated as true, theoutput goes high. Otherwise, it is low.[73] Logic Rule 3 See parameter group 13-4* Logic Rules. Iflogic rule 3 is evaluated as true, theoutput goes high. Otherwise, it is low.[74] Logic Rule 4 See parameter group 13-4* Logic Rules. Iflogic rule 4 is evaluated as true, theoutput goes high. Otherwise, it is low.[75] Logic Rule 5 See parameter group 13-4* Logic Rules. Iflogic rule 5 is evaluated as true, theoutput goes high. Otherwise, it is low.[80] SL DigitalOutput ASee parameter 13-52 SL Controller Action.The output goes high whenever the smartlogic action [38] Set digital out A high isParameter Description VLT® AQUA Drive FC 20282 Danfoss A/S © 05/2018 All rights reserved. MG20OB0233