YASKAWA F7 User Manual

Also see for Varispeed f7: Connection manual Programming manual User guide Instruction manual User manual

Contents

Electrical Installation 2 - 15Braking Transistor Unit(s) and Remote Mount Resistor Unit(s) Installation(for F7U2022 thru F7U2110 and F7U4022 thru F7U4300)Since the Remote Mount Resistor Unit generates heat during dynamic braking operation, install it to a noncombustible surfacein a location away from other equipment.Select mounting locations for Braking Transistor Unit(s) and Remote Mount Resistor Unit(s) so that wiring between the Driveand the Braking Transistor Unit is 16 feet (5m) or less, and the wiring between each Braking Transistor Unit and its associatedRemote Mount Resistor Unit, is less than 33 feet (10m).1. Mount the Braking Transistor Unit(s) on a vertical surface. The Braking Transistor Unit requires a minimum of 1.18 inches(30mm) clearance on each side and a minimum 3.94 inches (100mm) clearance top and bottom. Attach the Remote MountResistor Unit maintaining a minimum 1.97 inches (50mm) clearance on each side and a minimum 7.87 inches (200mm)clearance on top.2. In each Braking Transistor Unit, set the nominal line voltage jumper plug to the correct setting for the installation; this isfactory set at the 220V/440V/575V position. To access jumper plugs, remove the plastic cover.3. If multiple Braking Transistor Units are being installed, the unit closest to the Drive should have the Slave/Master jumperplug set to the “Master” position (factory setting); all others must have this jumper plug set to the “Slave” position.4. If a single Braking Transistor Unit and Remote Mount Resistor Unit are being installed, connect them to the Drive andexternal control circuitry according to the chart below and Fig 2.7.5. Power leads for the Remote Mount Resistor Unit generate high levels of electrical noise - these power leads must begrouped separately from all other leads.Table 2.10 Wire Size for Remote Mount Resistor Unit and Braking Transistor UnitName Circuit Terminals Wire Size AWG (mm2) Wire Type Terminal ScrewBraking Transistor Unit(Models CDBR-2015B,-2022B, -4030B, -4045B)Main 00 12-10 (3.5-5.5) 600V vinyl sheathed wireor equivalent M4Control 1 2 34 5 6 18-14 (0.75-2)Braking Transistor Unit(Model CDBR-2045, -4090)Main P, Po, N, B 12-10 (3.5-5.5) 600V vinyl sheathed wireor equivalentM5Control 1 2 34 5 6 18-14 (0.75-2) M4Braking Transistor Unit(Model CDBR-2110)Main P, Po, N, B 4 (22)8-6 (8-14) *1 600V vinyl sheathed wireor equivalentM6r s 12-10 (3.5-5.5)M4Control 1 2 34 5 6 18-14 (0.75-2)Braking Transistor Unit(Model CDBR-4220)Main P, Po, N, B 4 (22)8-6 (8-14) *1 600V vinyl sheathed wireor equivalentM6r s 12-10 (3.5-5.5)M4Control 1 2 34 5 6 18-14 (0.75-2)Braking Resistor Unit(Model LKEB-F)Main B P 12-10 (3.5-5.5) 600V vinyl sheathed wireor equivalentM4(M5) *2Control 1 2 18-14 (0.75-2) M4*1 For wire size of 8-6 (8-14), use UL1283 heat-resistant vinyl-insulated wire or equivalent.*2 M4 for Models LKEB-20P7 to -27P5 or -40P7 to -4015.M5 for Models LKEB-2011 to -2022 or -4018 to -4045.WARNING• Be sure to set the nominal line voltage selection jumper to match the level of the AC supply being applied to the Drive.• Failure to do so may result in improper operation.