Chapter 22-14F-2-412.2.8 Fixing the Machine in Place 0013-8269Color iR C3380G / Color iR C2880G / Color iR C3380i / Color iR C3380 /Color iR C2880i / Color iR C2880 / iR C3480 / iR C3480i / iR C3080 / iRC3080i / iR C25501) Move the host machine to its permanent position, and fix it in place usingthe 4 adjusters [1] of the cassette pedestal.F-2-422.2.9 Setting Up the Cassette 0013-8272Color iR C3380G / Color iR C2880G / Color iR C3380i / Color iR C3380 /Color iR C2880i / Color iR C2880 / iR C3480 / iR C3480i / iR C3080 / iRC3080i / iR C25501) Press the cassette release button, and slide out the cassette to the front.2) Check the type of paper that the user uses, check to see that the size con-figuration switch [1] of the cassette is set to the paper size. As necessary,change the switch position.3) Set the paper size dial [2] to suit the size of the paper in question.F-2-434) Pick the lever [1] of the side guide plate, and move the side guide plate tothe desired position.5) Shift down the rear guide plate [2] to the right to detach. Adjust the rearguide plate to suit the appropriate size indicated on the base of the cas-sette.F-2-446) Attach the cassette size label [1] that matches the selected size of paper tothe front of the cassette.F-2-457) Deposit paper in the cassette; then, slide in the cassette.8) Perform the same for the other cassette.9) If a cassette pedestal is used, set it by referring to its Installation Proce-dure.2.2.10 Automatic Gradation Correction 0013-8274Color iR C3380G / Color iR C2880G / Color iR C3380i / Color iR C3380 /Color iR C2880i / Color iR C2880 / iR C3480 / iR C3480i / iR C3080 / iRC3080i / iR C25501) Open the copyboard cover/DADF.2) Clean the host machine copyboard glass.3) Place A3, A4, 11X17, or LTR paper in the cassette. (See the instructionson how to set up the cassette.)4) Press the [Additional Function].5) Make the following selections: [Adjustment/Cleaning] > [Auto GradationAdjustment] > [Full Adjust] > [Test Print 1]- The test print 1 will be printed out.6) Place the printout of the test print 1 on the copyboard glass as instructedon the control panel screen.7) Close the copyboard cover/DADF.8) Press [Start Reading].- The machine reads the printout of the test print 1.- When a message appears prompting you to remove the test print, removethe printout of the test print 1 from the copyboard glass.9) Press [Test Print 2].- The machine prints out the test print 2.10) Place the printout of the test print 2 on the copyboard glass as instructedon the control panel scan.11) Close the copyboard cover/DADF.12) Press [Start Reading].- The machine reads the print out of the test print 2.- When a message appears promoting you to remove the test print, removethe printout of the test print 2 from the copyboard glass.13) Press [Test Print 3].- The machine prints the test print 3.14) Place the printout of the test print 3 on the copyboard glass as instructedon the control panel screen.MEMO:No need for adjustment in the case of no cassette pedestal.[1][1] [1][1][2]For models except ones with DADF, mount the accessory platen cover orthe DADF. When mounting the DADF, be sure to see the installationprocedure for the DADF.[1]
