10.5 b: Application402 YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical ManualNo.(Hex.) Name Description Default Setting(Range) Ref.b2-03(018B)DC Inject BrakingTime at Start Sets the DC Inject Braking Time at start. Configures the zero speedcontrol at start when using Closed Loop Vector Control, AdvancedOpen Loop Vector Control, or Closed Loop Vector Control for PM.A1-02 = 4: 0.03 sOther than A1-02 =4: 0.00 s(0.00 - 10.00 s)605b2-04(018C)DC Inject BrakingTime at Stop Sets the DC Inject Braking Time at stop. Configures the zero speedcontrol at stop when using Closed Loop Vector Control, AdvancedOpen Loop Vector Control, or Closed Loop Vector Control for PM.Determined by A1-02(0.00 - 10.00 s)606b2-08(0190)Magnetic FluxCompensationValue Sets the amount of current injected in the beginning of DC InjectionBraking at start (initial excitation) as a percentage of the value set inE2-03 [Motor No-Load Current].0%(0 - 1000%)606b2-12(01BA)Short Circuit BrakeTime @ Start Sets the Short Circuit Braking time at start.0.00 s(0.00 - 25.50 s)606b2-13(01BB)Short Circuit BrakeTime @ Start Sets the Short Circuit Braking time at stop.A1-02 = 8: 0.00 sOther than A1-02 =8: 0.50 s(0.00 - 25.50 s)607b2-18(0177)Short CircuitBraking Current Sets the Short Circuit Braking current as a percentage of the motorrated current.100.0%(0.0 - 200.0%)607◆ b3: Speed SearchNo.(Hex.) Name Description Default(Range) Ref.b3-01(0191)Speed SearchSelection at Start Sets whether to execute Speed Search or not with each Runcommand.0 : Disabled1 : EnabledDetermined by A1-02(0, 1)610b3-02(0192)Speed SearchDeactivationCurrent Sets the current level that ends Speed Search as a percentage of thedrive rated output current. Normally there is no need to change thissetting.Determined by A1-02(0 - 200%)611b3-03(0193)Speed SearchDeceleration Time Determines the deceleration time during Speed Search operation.Set the time it takes to decelerate from the maximum outputfrequency to the minimum output frequency.2.0 s(0.1 - 10.0 s)611b3-04(0194)V/f Gain duringSpeed Search Configures the ratio used to reduce the V/f during searches to reducethe output current during speed searches.Determined by o2-04(10 - 100)611b3-05(0195)Speed SearchDelay Time If a magnetic contactor is installed between the drive and the motor,this parameter sets a delay time to activate the magnetic contactorby delaying Speed Search.0.2 s(0.0 - 100.0 s)611b3-06(0196)Speed EstimationCurrent Level 1 Configure the amount of current that flows to the motor as acoefficient of the motor rated current when executing the SpeedEstimation Speed Search. Normally there is no need to change thissetting.Determined by o2-04(0.0 - 2.0)611b3-07(0197)Speed EstimationCurrent Level 2 The amount of current that flows to the motor when SpeedEstimation Speed Searches are executed is configured as acoefficient of E2-03 [Motor No-Load Current] or E4-03 [Motor 2Rated No-Load Current]. Normally there is no need to change thissetting.1.0(0.0 - 3.0)612V/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLVV/f CL-V/f OLV CLV AOLV OLV/PMOLV/PM AOLV/PM CLV/PM EZOLV
