Domain_1_Peer1(conf-if-po-100)# vlt-peer-lag port-channel 100Domain_1_Peer1(conf-if-po-100)# no shutdownAdd links to the eVLT port-channel on Peer 1.Domain_1_Peer1(conf)#interface range tengigabitethernet 1/16 - 1/17Domain_1_Peer1(conf-if-range-te-1/16-17)# port-channel-protocol LACPDomain_1_Peer1(conf-if-range-te-1/16-17)# port-channel 100 mode activeDomain_1_Peer1(conf-if-range-te-1/16-17)# no shutdownNext, configure the VLT domain and VLTi on Peer 2.Domain_1_Peer2#configureDomain_1_Peer2(conf)#interface port-channel 1Domain_1_Peer2(conf-if-po-1)# channel-member TenGigabitEthernet 1/8-1/9Domain_1_Peer2(conf) #vlt domain 1000Domain_1_Peer2(conf-vlt-domain)# peer-link port-channel 1Domain_1_Peer2(conf-vlt-domain)# back-up destination 10.16.130.12Domain_1_Peer2(conf-vlt-domain)# system-mac mac-address 00:0a:00:0a:00:0aDomain_1_Peer2(conf-vlt-domain)# peer-routingDomain_1_Peer2(conf-vlt-domain)# unit-id 1Configure eVLT on Peer 2.Domain_1_Peer2(conf)#interface port-channel 100Domain_1_Peer2(conf-if-po-100)# switchportDomain_1_Peer2(conf-if-po-100)# vlt-peer-lag port-channel 100Domain_1_Peer2(conf-if-po-100)# no shutdownAdd links to the eVLT port-channel on Peer 2.Domain_1_Peer2(conf)#interface range tengigabitethernet 1/28 - 1/29Domain_1_Peer2(conf-if-range-te-1/28-29)# port-channel-protocol LACPDomain_1_Peer2(conf-if-range-te-1/28-29)# port-channel 100 mode activeDomain_1_Peer2(conf-if-range-te-1/28-29)# no shutdownIn Domain 2, configure the VLT domain and VLTi on Peer 3.Domain_2_Peer3#configureDomain_2_Peer3(conf)#interface port-channel 1Domain_2_Peer3(conf-if-po-1)# channel-member TenGigabitEthernet 1/8-1/9Domain_1_Peer3#no shutdownDomain_2_Peer3(conf)#vlt domain 200Domain_2_Peer3(conf-vlt-domain)# peer-link port-channel 1Domain_2_Peer3(conf-vlt-domain)# back-up destination 10.18.130.11Domain_2_Peer3(conf-vlt-domain)# system-mac mac-address 00:0b:00:0b:00:0bDomain_2_Peer3(conf-vlt-domain)# peer-routingDomain_2_Peer3(conf-vlt-domain)# unit-id 0Configure eVLT on Peer 3.Domain_2_Peer3(conf)#interface port-channel 100Domain_2_Peer3(conf-if-po-100)# switchportDomain_2_Peer3(conf-if-po-100)# vlt-peer-lag port-channel 100Domain_2_Peer3(conf-if-po-100)# no shutdownAdd links to the eVLT port-channel on Peer 3.Domain_2_Peer3(conf)#interface range tengigabitethernet 1/19 - 1/20Domain_2_Peer3(conf-if-range-te-1/19-20)# port-channel-protocol LACPDomain_2_Peer3(conf-if-range-te-1/19-20)# port-channel 100 mode activeDomain_2_Peer3(conf-if-range-te-1/19-20)# no shutdownNext, configure the VLT domain and VLTi on Peer 4.Domain_2_Peer4#configureDomain_2_Peer4(conf)#interface port-channel 1Domain_2_Peer4(conf-if-po-1)# channel-member TenGigabitEthernet 1/8-1/91018 Virtual Link Trunking (VLT)
