provider at Level 4 VLAN 3000%ECFM-5-ECFM_REMOTE_ALARM: Remote CCM Defect detected by MEP 3 in Domaincustomer1 at Level 7 VLAN 1000%ECFM-5-ECFM_RDI_ALARM: RDI Defect detected by MEP 3 in Domain customer1 atLevel 7 VLAN 1000entityEnable entity change trapsTrap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1487406) 4:07:54.06,SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 4Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1488564) 4:08:05.64,SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 5Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1489064) 4:08:10.64,SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 6Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1489568)4:08:15.68,SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 7SNMP Copy Config Command Completed%RPM0-P:CP %SNMP-4-RMON_RISING_THRESHOLD: STACKUNIT0 rising threshold alarm fromSNMP OID %RPM0-P:CP %SNMP-4-RMON_FALLING_THRESHOLD: STACKUNIT0 falling threshold alarm fromSNMP OID %RPM0-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD: STACKUNIT0 high-capacity rising thresholdalarm from SNMP OID Enabling an SNMP Agent to Notify Syslog ServerFailureYou can configure a network device to send an SNMP trap if an audit processing failure occurs due to loss of connectivity with the syslogserver.If a connectivity failure occurs on a syslog server that is configured for reliable transmission, an SNMP trap is sent and a message isdisplayed on the console.The SNMP trap is sent only when a syslog connection fails and the time-interval between the last syslog notification and current time isgreater than or equal to 5 minutes. This restriction also applies to the console message.NOTE: If a syslog server failure event is generated before the SNMP agent service starts, the SNMP trap is not sent.To enable an SNMP agent to send a trap when the syslog server is not reachable, enter the following command:CONFIGURATION MODEsnmp-server enable traps snmp syslog-unreachableTo enable an SNMP agent to send a trap when the syslog server resumes connectivity, enter the following command:CONFIGURATION MODEsnmp-server enable traps snmp syslog-reachableTable 90. List of Syslog Server MIBS that have read accessMIB Object OID Object Values DescriptiondF10SysLogTraps 1.3.6.1.4.1.6027.3.30.1.1 1 = reachable2 = unreachable Specifies whether the syslogserver is reachable orunreachable.Simple Network Management Protocol (SNMP) 869
