Configuring Logging FormatTo display syslog messages in a RFC 3164 or RFC 5424 format, use the logging version {0 | 1} command in CONFIGURATIONmode. By default, the system log version is set to 0.The following describes the two log messages formats:• 0 – Displays syslog messages format as described in RFC 3164, The BSD syslog Protocol• 1 – Displays syslog message format as described in RFC 5424, The SYSLOG ProtocolExample of Configuring the Logging Message FormatDell(conf)#logging version ?<0-1> Select syslog version (default = 0)Dell(conf)#logging version 1Display the Logging Buffer and the Logging ConfigurationTo display the current contents of the logging buffer and the logging settings for the system, use the show logging command in EXECprivilege mode. When RBAC is enabled, the security logs are filtered based on the user roles. Only the security administrator and systemadministrator can view the security logs.Example of the show logging CommandDell#show loggingsyslog logging: enabledConsole logging: level DebuggingMonitor logging: level DebuggingBuffer logging: level Debugging, 40 Messages Logged, Size (40960 bytes)Trap logging: level Informational%IRC-6-IRC_COMMUP: Link to peer RPM is up%RAM-6-RAM_TASK: RPM1 is transitioning to Primary RPM.%RPM-2-MSG:CP1 %POLLMGR-2-MMC_STATE: External flash disk missing in 'slot0:'%CHMGR-5-CARDDETECTED: Line card 0 present%CHMGR-5-CARDDETECTED: Line card 2 present%CHMGR-5-CARDDETECTED: Line card 4 present%CHMGR-5-CARDDETECTED: Line card 5 present%CHMGR-5-CARDDETECTED: Line card 8 present%CHMGR-5-CARDDETECTED: Line card 10 present%CHMGR-5-CARDDETECTED: Line card 12 present%TSM-6-SFM_DISCOVERY: Found SFM 0%TSM-6-SFM_DISCOVERY: Found SFM 1%TSM-6-SFM_DISCOVERY: Found SFM 2%TSM-6-SFM_DISCOVERY: Found SFM 3%TSM-6-SFM_DISCOVERY: Found SFM 4%TSM-6-SFM_DISCOVERY: Found SFM 5%TSM-6-SFM_DISCOVERY: Found SFM 6%TSM-6-SFM_DISCOVERY: Found SFM 7%TSM-6-SFM_SWITCHFAB_STATE: Switch Fabric: UP%TSM-6-SFM_DISCOVERY: Found SFM 8%TSM-6-SFM_DISCOVERY: Found 9 SFMs%CHMGR-5-CHECKIN: Checkin from line card 5 (type EX1YB, 1 ports)%TSM-6-PORT_CONFIG: Port link status for LC 5 => portpipe 0: OK portpipe 1: N/A%CHMGR-5-LINECARDUP: Line card 5 is up%CHMGR-5-CHECKIN: Checkin from line card 12 (type S12YC12, 12 ports)%TSM-6-PORT_CONFIG: Port link status for LC 12 => portpipe 0: OK portpipe 1: N/A%CHMGR-5-LINECARDUP: Line card 12 is up%IFMGR-5-CSTATE_UP: changed interface Physical state to up: So 12/8%IFMGR-5-CSTATE_DN: changed interface Physical state to down: So 12/8To view any changes made, use the show running-config logging command in EXEC privilege mode.68 Management