Raymarine ST70 Instrument manuals
ST70 Instrument
Table of contents
- installation guide
- Table Of Contents
- emc installation guidelines
- product disposal
- Chapter 1:Before you begin
- Product documents
- Chapter 2:Planning
- Positioning the ST70 autopilot controller
- Parts supplied
- Parts not supplied
- Chapter 3:Installation
- seatalk systems
- Commissioning
- Chapter 4:Technical specifications
- Chapter 5:Templates
ST70 Instrument
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- safety notices
- product disposal
- Introduction
- Sail boat Pilot Controller keypad
- Instrument keypad
- Commonly used control functions
- Setup principles
- display types & grouping
- Normal operation
- user setup
- Power boat functions
- System information
- Commissioning requirement
- Requirement
- Switch on
- Setting Vessel Type
- Setting date format
- Setting time format
- Data units
- Leaving units setup
- Dockside wizard
- Rudder and motor checks for systems with a Rudder Reference transducer
- Rudder and motor checks for systems without a Rudder Reference transducer
- Hard over time
- Depth offsets
- Calibrating conventional transducers
- Setting water temperature
- Calibrating trim tabs
- Setting magnetic variation
- Changing display response rate
- Rudder limit
- Open water calibration
- Starting open water calibration
- Aligning the compass to GPS
- AutoLearn
- Next actions
- Wind transducer setup
- Alignment
- Speed calibration for conventional speed transducer
- Manual speed calibration
- Speed calibration for smart transducer
- Add point
- Checking rudder gain
- Rudder damping
- General setup
- Changing vessel type
- Autopilot setup
- Setting rudder gain
- Setting turn rate limit
- Setting rudder offset
- AutoTurn
- Additional sail boat settings
- Gybe inhibit
- System configuration
- Maintenance
- Cleaning
- Using the display self-monitoring features
- About Pilot
- Appendix 1:Specifications
- Pilot Controller (power boat) keypad
- Appendix 2:Glossary
- Index
ST70 Instrument
Table of contents
- emc installation guidelines
- product disposal
- product documents
- Table Of Contents
- Table Of Contents
- Chapter 1:ST70 Overview
- Display and controls
- Operating principles
- System functionality
- Chapter 2:Setup Procedures
- Dockside and open water procedures
- Display settings
- Autopilot calibration
- Response Levels
- Sailboat setup procedures
- Wind Trim
- Power boat and fishing boat setup procedures
- SmartPilot Functions
- Extended systems
- Power and fishing boat menus
- Pilot view
- Using the SmartPilot to steer your boat
- Using preset patterns
- Activating Track mode
- Leaving Track mode
- Cross track error
- Tidal stream compensation
- Steering to the next waypoint in a route
- Waypoint Advance warning
- Using the SmartPilot with sail boats
- WindTrim
- Operating hints for Wind Vane mode
- Chapter 4:Maintenance and troubleshooting
- Troubleshooting
- st70 pilot controller reference guide
- Using the About Display feature
- Technical support
- telephone help line
- Chapter 5:Alarms
- Chapter 6:Data List
- Chapter 7:Vessel Settings
- Chapter 8:Technical specifications
ST70 Instrument
Table of contents
ST70 Instrument
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- warnings and cautions
- emc installation guidelines
- technical accuracy
- general information
- power supplies
- dedicated display power supply
- parts supplied
- parts not supplied
- display power cables
- seatalk ng connections
- mounting procedure
- installing transducers
- smart transducers
- autopilot calibration
- initial setup
- selecting language
- select type
- date & time
- setting local time
- changing units
- initial setup end routine
- hard over time
- end of autopilot dockside setup
- accessing transducer setup
- calibrating conventional transducers
- calibrating smart transducers
- calibrating trim tabs
- miscellaneous setup
- changing display response rate
- rudder limit
- open water calibration
- starting open water calibration
- requirement for a clear area
- instrument system calibration
- wind transducer setup
- speed calibration
- speed calibration for conventional speed transducer
- speed calibration for smart transducer
- return to normal operation
- checking rudder gain
- emc conformance
- all types
- pilot controller (power boat) keypad
- flush mount
- surface mount
ST70 Instrument
Table of contents
- emc conformance
- Getting started
- general operation
- Display grouping & control
- Setting display brightness
- Setting the correct local time
- Setting the screen colors
- Choosing the data units
- Setting up a Pilot Controller display
- setting up data boxes
- Basic autopilot operation
- Using AutoTack
- Using autopilot Track mode
- Using autopilot Wind Vane mode
- Using autopilot fishing patterns
- Switching instrument pages on & off
- Setting instrument page rollover
- Changing information on a
- Changing the page layout
- Using alarm clock
- Using race timers
- Setting alarms
- Alarm events
ST70 Instrument
Table of contents
- Table Of Contents
- Table Of Contents
- safety notices
- product disposal
- Chapter 1:ST70 General Information
- Setup functions
- Instruments not requiring commissioning
- Normal operation
- Day-to-day setting up
- Power protocol
- Chapter 2:Commissioning Procedures
- Initial setup
- Setting date format
- Setting local time
- Leaving units setup
- Requirement
- Set water temperature
- Set ground wind
- Changing response rate
- Ending dockside setup
- Preliminary procedures
- Alignment
- Calibrate wind speed
- Start speed calibration
- Manual calibration
- Return to normal operation
- Chapter 3:Setup Procedures
- Leaving Advanced Options
- Setting time format
- Chapter 4:Maintenance & Troubleshooting
- Troubleshooting
- Using About Display feature
- Technical support
- Telephone help line
- Specification
- Glossary
- Index
ST70 Instrument
Table of contents
- Table Of Contents
- warnings and cautions
- emc servicing and maintenance
- product disposal
- Chapter 1:Before you begin
- Chapter 2:Planning
- Positioning the ST70 instrument
- Parts supplied
- Parts not supplied
- Chapter 3:Installation
- Install transducers
- Final fix
- Chapter 4:Technical specifications
- Chapter 5:Templates
- surface mount
manualsdatabase
Your AI-powered manual search engine