Part Number Designation68C3 Operations Manual North Atlantic Industries, Inc. 12/19/2014Rev: 2014-12-19-0947 www.naii.com Page 324 of 330Part Number NotesNote 1: Synchro/Resolver four channel Measurement module selection:(For ranges other than those listed contact factory. Customer should indicate the actual frequency applicable to his design toassure that the correct default band width is set at the factory); Frequency band tolerance +/- 20%; Voltage tolerance +/- 10%.Module Input Reference FrequencyCode Voltage Voltage Band RemarksSA 2-28 VL-L 2-115 Vrms 50 Hz - 400 Hz All Input and Reference voltages are auto rangingSB 2-28 VL-L 2-115 Vrms 400 Hz - 1 KHz All Input and Reference voltages are auto rangingSC 2-28 VL-L 2-115 Vrms 1 KHz - 3 KHz All Input and Reference voltages are auto rangingSD 2-28 VL-L 2-115 Vrms 3 KHz - 5 KHz All Input and Reference voltages are auto rangingSE 2-28 VL-L 2-115 Vrms 5 KHz - 7 KHz All Input and Reference voltages are auto rangingSF 2-28 VL-L 2-115 Vrms 7 KHz - 10 KHz All Input and Reference voltages are auto rangingSG* 2-28 VL-L 2-115 Vrms 10 KHz - 20 KHz All Input and Reference voltages are auto rangingSH 90 VL-L 115 Vrms 50 Hz - 400 HzSJ 90 VL-L 115 Vrms 400 Hz - 1 KHzSX x x x Special configurations, contact factory*Consult factory for availabilityNote 2: LVDT/RVDT four channel Measurement module selection:(For ranges other than those listed contact factory. Customer should indicate the actual frequency applicable to his design toassure that the correct default band width is set at the factory.) Frequency band tolerance +/- 20%. Voltage tolerance +/- 10%.Module Input Reference FrequencyCode Voltage Voltage Band RemarksLB 2-28 VL-L 2-28 Vrms 400 Hz - 1 KHz All Input and Reference voltages are auto rangingLC 2-28 VL-L 2-28 Vrms 1 KHz - 3 KHz All Input and Reference voltages are auto rangingLD 2-28 VL-L 2-28 Vrms 3 KHz - 5 KHz All Input and Reference voltages are auto rangingLE 2-28 VL-L 2-28 Vrms 5 KHz - 7 KHz All Input and Reference voltages are auto rangingLF 2-28 VL-L 2-28 Vrms 7 KHz - 10 KHz All Input and Reference voltages are auto rangingLG 2-28 VL-L 2-28 Vrms 10 KHz - 20 KHz All Input and Reference voltages are auto rangingLX x x x Special configurations, contact factory*Consult factory for availabilityNote 3: Can only specify either the KA Combo Module or the Onboard Reference Supply in Slot 3Note 4: Contact factory for availabilityNote 5:Warning: Maximum ratings for the Tyco MultiGig-RT2 type rear I/O connectors are as follows (per Tyco 108-2072): 50 V peak AC or 50 VDC 1A @ 30 deg.Ensure module operation characteristics are within the maximum limits of the rear I/O connector limitations.Note 6:Module Output FrequencyCode VL-L BandW1 2-115 Vrms 47 Hz - 20 KHz (see spec for applicable Vout ranges)W2 2-28 Vrms 47 Hz - 10 KHz (see spec for applicable Vout ranges)W3 28-115 Vrms 47 Hz – 2.5 KHzNote: W1 only utilizes a mechanical relay for range switching. May not be suitable for some embedded system applications.Note 7: Following are the module designation selections for D/S and L/RVDT (DLV) simulation modules):
