February, 20082-100 WorkCentre 5225, 5230012-151 (A-Finisher)Launch VersionStatus Indicator Raps012-151 (A-Finisher) Compiler Exit Sensor OFF JamBSD-ON:12.3The Compile Exit Sensor does not turn Off within a specified time after it has turned On.Initial Actions• Check the Compile Exit Sensor is properly installed and free from foreign objects and thatthe actuator is not binding.• Power Off/On.ProcedureCheck the specifications of paper. Paper is in spec.Y NReplace the paper with new paper that is in spec.Check the condition of the paper. The paper is in normal condition without any problemthat causes the paper to be bent or caught.Y NResolve any problem that causes the paper to be bent or caught.Check the transport path for a foreign object, deformed part, and paper dust. The transportpath is in normal condition with no foreign object, deformed part and paper dust.Y NRepair the deformed part(s) and remove the foreign object(s) and paper dust.Check the Transport Roll for wear, deterioration and paper dust. The Transport Roll is innormal condition, not worn and deteriorated and with no paper dust.Y NRemove the paper dust and replace the worn or deteriorated Transport Roll.Check the drive mechanism to the Transport Roll for a deformed, broken part, and/or belt dam-age. The drive mechanism is free of defects.Y NRepair defects or damage to the drive mechanism.Enter Component Control [012-150]. Actuate the Compile Exit Sensor. The display changes.Y NCheck the connections of P/J8709 and P/J8728. P/J8709 and P/J8728 are securelyconnected.Y NConnect P/J8709 and P/J8728 securely.Check for an open or short circuit between J8709 and J8728. The wire J8709 andJ8728 are OK.Y NRepair the open or short circuit.Measure the voltage between Finisher PWB J8709-3 (+) and GND (-). The voltage isapprox. +5VDC.Y NGo to Wirenet A-Finisher +5VDC and check the +5VDC circuit.Measure the voltage between Finisher PWB J8709-2 (+) and GND (-). Actuate the Com-pile Exit Sensor. The voltage changes.Y NReplace the Compile Exit Sensor (PL 22.5).Check the wires and connectors for an intermittent open or short circuit. If the problemcontinues, replace the Finisher PWB (PL 22.7).Enter Component Control [012-095]. The Finisher Transport Motor rotates.Y NCheck the connections of P/J8706 and P/J8739. P/J8706 and P/J8739 are securelyconnected.Y NConnect P/J8706 and P/J8739 securely.Check for an open or short circuit between J8706 and J8736. The wire between J8706and J8736 are OK.Y NRepair the open or short circuit.Measure the voltage between Finisher PWB J8706-5 (+) and GND (-), and between Fin-isher PWB J8706-7 (+) and GND (-). Each voltage is approx. +24VDC.Y NGo to Wirenet A-Finisher +24VDC and check the +24VDC circuit.Check the wires and connectors for an intermittent open or short circuit. If the problemcontinues, replace the Finisher Transport Motor (PL 22.4). If the problem persists, replacethe Finisher PWB (PL 22.7).Enter [012-013]. When the Sub Paddle Solenoid is turned On/Off, the Sub Paddle ShaftAssembly goes down/up.Y NCheck the Sub Paddle mechanism for a deformed or broken part and not-seated gears.The Sub Paddle mechanism is free from defects and gears are seating properly.Y NRepair defeats to the Sub Paddle mechanism.Check the connections of P/J8705 and P/J8734. P/J8705 and P/J8734 are securelyconnected.Y NConnect P/J8705 and P/J8734 securely.Check for an open or short circuit between J8705 and J8734. The wires betweenJ8705 and J8734 are OK.Y NRepair the open or short circuit.Measure the voltage between Finisher PWB J8705-1 (+) and GND (-). The voltage isapprox. +24VDC.AAB
