February, 20082-532 WorkCentre 5225, 5230073-210Launch VersionStatus Indicator Raps073-210 Tray 3 Lift Up Failure RAPBSD-ON:7.9/7.11• After the 2TM-Tray 3 Feed/Lift Motor turned On, the 2TM-Tray 3 Level Sensor did not turnOn within the specified time.• After the TTM-Tray 3 Feed/Lift Motor turned On, the TTM-Tray 3 Level Sensor did not turnOn within the specified time.Initial Actions• Reload paper in the tray correctly.• Remove foreign substances in the tray.• Power OFF/ONProcedureRemove the tray and reinstall. The Tray 3 Feed/Lift Motor can be heard.Y NExecute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 3 Feed/LiftMotor (PL 12.3/PL 13.6) can be heard.Y NCheck the connections of P/J220B, P/J661B and P/J549. P/J220B, P/J661Band P/J549 are connected correctly.Y NConnect P/J220B, P/J661B and P/J549.Remove the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) and the Tray 4 Feed/Lift Motor(PL 12.3/PL 13.6).Replace the Tray 3 Feed/Lift Motor with the Tray 4 Feed/Lift Motor.Execute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 4Feed/Lift Motor (PL 12.3/PL 13.6) can be heard.Y NReturn the Tray 3 Feed/Lift Motor to its original position.Check the wire between J220B and J549 for an open circuit or a short circuit(BSD 7.9 Flag 1 / BSD 7.11 Flag 1). The wire between J220B and J549 isconducting without an open circuit or a short circuit.Y NRepair the open circuit or short circuit.Replace the Tray Module PWB (PL 12.6/PL 13.8).Return the Tray 4 Feed/Lift Motor to its original position.Replace the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6).Go to the OF 2 (SIZE SWITCH ASSY RAP).Check the installation of the Tray 3 Level Sensor (PL 12.3/PL 13.6) and the operation of theactuator. The Tray 4 Level Sensor is installed correctly and the actuator works.Y NReinstall the Tray 4 Level Sensor.Execute Component Control [071-208 Tray 3 Level Sensor]. Manually activate the Tray 3 LevelSensor (PL 12.3/PL 13.6). The display changes.Y NCheck the connections of P/J101B, P/J661B and P/J549. P/J101B, P/J661B and P/J549 are connected correctly.Y NConnect P/J101B, P/J661B and P/J549.Check the wire between J101B and J549 for an open circuit or a short circuit (BSD 7.9Flag 2/Flag 3 / BSD 7.11 Flag 2/Flag 3). The wire between J101B and J549 is con-ducting without an open circuit or a short circuit.Y NRepair the open circuit or short circuit.Measure the voltage between the Tray Module PWB P549-B7 (+) and GND (-) (BSD 7.9Flag 3 / BSD 7.11 Flag 3). The voltage is approx. +5VDC.Y NReplace the Tray Module PWB (PL 12.6/PL 13.8).Measure the voltage between the Tray Module PWB P549-B9 (+) and GND (-) (BSD 7.9Flag 2 / BSD 7.11 Flag 2).Activate the actuator of the Tray 3 Level Sensor (PL 12.3/PL 13.6). The voltagechanges.Y NReplace the Tray 3 Level Sensor (PL 12.3/PL 13.6).Replace the Tray Module PWB (PL 12.6/PL 13.8).Replace the Tray Module PWB (PL 12.6/PL 13.8).AA
