February, 20082-535WorkCentre 5225, 5230 074-101Status Indicator RapsLaunch Version074-101 Tray 4 Miss Feed JAM RAPBSD-ON:3.3/7.10/8.5After the Tray 4 Feed/Lift Motor turned On, the Tray 4 Feed Out Sensor did not turn On withinthe specified time.Initial Actions• Power OFF/ONProcedureCheck the Transport Roll for wear and paper powder. The Transport Roll is ok.Y NReplace the Transport Roll.Check for foreign substances, distortion and paper powder in the paper transport path. Nodistortion, foreign substances, or paper powder are found in the paper transport path.Y NClear away the foreign substances and paper powder. Correct the distortion.Execute Component Control [071-102 Tray 4 Feed Out Sensor]. Actuate the Tray 4 Feed OutSensor (PL 12.5/PL 13.4) with paper. The display changes.Y NCheck the connections of P/J825, P/J842, P/J548, P/J541 and P/J413. The connec-tors are connected correctly.Y NConnect the connectors.Check the wire between J825 and J548 for an open circuit or a short circuit (BSD 8.5).The wire between J825 and J548 is conducting without an open circuit or a shortcircuit.Y NRepair the open circuit or short circuit.Measure the voltage between the Tray Module PWB P548-1 (+) and GND (-) (BSD 8.5).The voltage is approx. +5VDC.Y NReplace the Tray Module PWB (PL 12.6/PL 13.8).Measure the voltage between the Tray Module PWB P548-3 (+) and GND (-) (BSD 8.5).Actuate the Tray 4 Feed Out Sensor (PL 12.5/PL 13.4) with paper. The voltagechanges.Y NReplace the Tray 4 Feed Out Sensor (PL 12.5/PL 13.4).Check the wire between J541-11 and J413-B5 for an open circuit or a short circuit (BSD3.3 Flag 2). The wire between J541-11 and J413-B5 is conducting without an opencircuit or a short circuit.Y NRepair the open circuit or short circuit.Measure the voltage between the MCU PWB P413-B5 (+) and GND (-) (BSD 3.3 Flag 2).Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The voltagechanges.Y NReplace the Tray Module PWB (PL 12.6/PL 13.8).Replace the MCU PWB (PL 9.1).Execute Component Control [073-010 Tray 4 Feed/Lift Motor ON]. The Tray 4 Feed/LiftMotor (PL 12.3/PL 13.6) can be heard.Y NCheck the connections of P/J220A, P/J661A, P/J549, P/J541 and P/J413. P/J220A,P/J661A, P/J549, P/J541 and P/J413 are connected correctly.Y NConnect P/J220A, P/J661A, P/J549, P/J541 and P/J413.Remove the Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6) and the Tray 3 Feed/Lift Motor (PL12.3/PL 13.6).Replace the Tray 4 Feed/Lift Motor with the Tray 3 Feed/Lift Motor.Execute Component Control [073-010 Tray 4 Feed/Lift Motor ON]. The Tray 3 Feed/LiftMotor (PL 12.3/PL 13.6) can be heard.Y NReturn the Tray 3 Feed/Lift Motor to its original position.Check the wire between J220A and J549 for an open circuit or a short circuit (BSD7.10 Flag 1 / BSD 7.12 Flag 1). The wire between J220A and J549 is conductingwithout an open circuit or a short circuit.Y NRepair the open circuit or short circuit.Replace the Tray Module PWB (PL 12.6/PL 13.8).Return the Tray 3 Feed/Lift Motor to its original position.Replace the Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6).Replace the Tray Module PWB (PL 12.6/PL 13.8).AA
