February, 20082-102 WorkCentre 5225, 5230012-152 (A-Finisher), 012-161 (A-Finisher)Launch VersionStatus Indicator RapsY NRepair the open or short circuit.Measure the voltage between Finisher PWB J8709-3 (+) and GND (-). The voltage isapprox. +5VDC.Y NGo to Wirenet A-Finisher +5VDC and check the +5VDC circuit.Measure the voltage between Finisher PWB J8709-2 (+) and GND (-). Actuate the Com-pile Exit Sensor. The voltage normally changes.Y NReplace the Compile Exit Sensor (PL 22.5).Check the wires and connectors for an intermittent open or short circuit. If the problemcontinues, replace the Finisher PWB (PL 22.7).Enter [012-095]. The Finisher Transport Motor rotates.Y NCheck the connections of P/J8706 and P/J8739. P/J8706 and P/J8739 are securelyconnected.Y NConnect P/J8706 and P/J8739 securely.Check for an open or short circuit between J8706 and J8739. The wire between J8706and J8739 are OK.Y NRepair the open or short circuit.Measure the voltage between Finisher PWB J8706-5 (+) and GND (-), and J8706-7 (+)and GND (-). Each voltage is approx. +24VDC.Y NGo to Wirenet A-Finisher +24VDC and check the +24VDC circuit.Check the wires and connectors for an intermittent open or short circuit. If the problemcontinues, replace the Finisher Transport Motor (PL 22.4). If the problem persists, replacethe Finisher PWB (PL 22.7).Check the wires and connectors for an intermittent open or short circuit. If the problem contin-ues, replace the Finisher PWB (PL 22.7).012-161 (A-Finisher) Set Eject JamBSD-ON:12.3In the Eject Motor’s ejecting operation, Eject Home Sensor ON was detected within a specifiedtime after the start of the reverse operation of the Eject Motor.(The Eject Motor should have ejected paper, but returned Home earlier than specified.)Initial Actions• Check the Eject Home Sensor is properly installed, not broken, and has no foreign object.• Power Off/On.ProcedureCheck the specifications of paper. Paper is in spec.Y NReplace the paper with new paper that is in spec.Check the condition of the paper. The paper is in normal condition without any problemthat causes the paper to be bent or caught.Y NResolve any problem that causes the paper to be bent or caught.Check the Eject mechanism for deformed parts, broken parts, and/or belt damage. The Ejectmechanism free from defects.Y NRepair the Eject mechanism.Enter Component Control [012-252]. Block and unblock the Eject Home Sensor with a piece ofpaper. The display changes.Y NCheck the connections of P/J8700 and P/J8725. P/J8700 and P/J8725 are securelyconnected.Y NConnect P/J8700 and P/J8725 securely.Check for an open or short circuit between J8700 and J8725. The wires betweenJ8700 and J8725 are OK.Y NRepair the open or short circuit.Measure the voltage between Finisher PWB J8700-9 (+) and GND (-). The voltage isapprox. +5VDC.Y NGo to Wirenet A-Finisher +5VDC and check the +5VDC circuit.Measure the voltage between Finisher PWB J8700-8 (+) and GND (-). Block and unblockthe Eject Home Sensor with a piece of paper. The voltage changes.Y NReplace the Eject Home Sensor (PL 22.10).AA B
