8.2 Drive Options and Peripheral DevicesTable 8.1 lists the names of the various peripheral devices, accessories, and options available for Yaskawa drives. ContactYaskawa or your Yaskawa agent to order these peripheral devices.• Peripheral Device Selection: Refer to the Yaskawa catalog for selection and part numbers.• Peripheral Device Installation: Refer to the corresponding option manual for installation instructions.Table 8.1 Available Peripheral DevicesOption Model Number DescriptionPower OptionsDC link choke – Improves the power factor by suppressing harmonic distortion from the power supply.AC Reactor – Protects the drive when operating from a large power supply and improves the power factor bysuppressing harmonic distortion. Highly recommended for power supplies that exceed 600 kVA.Braking Resistor –For use with systems that require dynamic braking with up to 3% ED. If higher ED is required,use a Braking Resistor Unit.Note: Not rated for 600 V class drive models.Input/Output Option CardsAnalog Monitor AO-A3• Provides extra multi-function analog output terminals• Output channels: 2• Output voltage: -10 to 10 V, 11-bit (signed)Communication Option CardsEtherNet/IP SI-EN3 Connects to an EtherNet/IP network.Modbus TCP/IP SI-EM3 Connects to a Modbus TCP/IP network.PROFINET <1> SI-EP3 Connects to a PROFINET network.DeviceNet SI-N3 Connects to a DeviceNet networkPROFIBUS-DP SI-P3 Connects to a PROFIBUS-DP network.MECHATROLINK-II SI-T3 Connects to a MECHATROLINK-II network.BACnet SI-B3 Connects to a BACnet network.CC-Link <2> SI-C3 Connects to a CC-Link networkCANopen <2> SI-S3 Connects to a CANopen network.Interface OptionsRemote Operator Cable UWR000051, 1 m cableUWR000052, 2 m cable RJ-45, 8-pin straight through, UTP CAT5e, extension cable (1 m or 2 m) to connect the digitaloperator for remote operation.USB Copy Unit JVOP-181 • Allows the user to copy and verify parameter settings between drives.• Functions as an adapter to connect the drive to a USB port on a PC.Mechanical OptionsAttachment for ExternalHeatsink EZZ020800A/B/C/D Installation kit for mounting the drive with the heatsink outside of the panel (Side-by-Sidemounting possible)IP20/NEMA Type 1 Kit 100-054-503100-054-504 Parts to make the drive conform to IP20/NEMA Type 1 enclosure requirements.IP20/NEMA Type 1, 4, 12Blank Keypad Kit UUX0000526Provides digital operator (JVOP-180, JVOP-182) functionality on an enclosure designed forIP20/NEMA Type 1, 3R, 4, 4X, 12, or IPo6 environment. This keypad has a blank label on thefront.IP20/NEMA Type 1, 4, 12Yaskawa Logo Keypad Kit UUX0000527Provides digital operator (JVOP-180, JVOP-182) functionality on an enclosure designed forIP20/NEMA Type 1, 3R, 4, 4X, 12, or IPo6 environment. This keypad has a Yaskawa brandlabel on the front.Others24 V Power Supply 200 V Class: PS-A10LB400 V Class: PS-A10HB600 V Class: PS-A10HB Supplies the drive controller with 24 Vdc power during main power loss.PC Software ToolsDriveWizard Industrial Contact Yaskawa PC tool for drive setup and parameter management<1> Available in drive software versions PRG: 8503 and later.<2> Limited support. Contact a Yaskawa representative or the nearest Yaskawa sales office for assistance.8.2 Drive Options and Peripheral Devices376 YASKAWA SIEP YAIP1U 01C AC Drive - P1000 Technical Manual
