H2 Multi-Function Digital Output SettingsH2-ooSetting Function Description Page1E Restart enabled Closed: An automatic restart is performed 2221F Motor overload alarm (oL1) Closed: oL1 is at 90% of its trip point or greater. An oH3 situation also triggers this alarm. 22220 Drive overheat pre-alarm (oH) Closed: The heatsink temperature exceeds the L8-02 level (while L8-03 = 3 or 4), or an externaldevice has triggered an oH2 alarm via multi-function input H1-oo = B. 22222 Mechanical weakeningdetection Closed: Mechanical weakening detected. 2222F Maintenance period Closed: Cooling fan, electrolytic capacitors, IGBTs, or the soft charge bypass relay may requiremaintenance. 22237 During frequency outputOpen: Either the drive has stopped or baseblock, DC Injection Braking, or Initial Excitation isbeing performed.Closed: Drive is running the motor (not in a baseblock state and DC Injection is not beingperformed).22238 Drive enabled Closed: Multi-function input set for “Drive enable” is closed (H1-oo = 6A) 22339 Watt hour pulse output Output units are determined by H2-06. Outputs a pulse every 200 ms to indicate the kWh count. 2233C LOCAL/REMOTE status Open: REMOTEClosed: LOCAL 2233D During speed search Closed: Speed Search is being executed. 2233E PID feedback low Closed: PID feedback level is too low. 2233F PID feedback high Closed: The PID feedback level is too high. 2234A During KEB Ride-Thru Closed: KEB Ride-Thru is being performed. 2234C During fast stop Closed: A Fast Stop command has been entered from the operator or input terminals. 2234D oH Pre-alarm time limit Closed: An oH pre-alarm is present after 10 output frequency reduction cycles have passed (L8-03= 4). 2234E Braking transistor fault (rr) Closed: The built-in dynamic braking transistor failed. 2234F Braking resistor overheat (oH) Closed: The dynamic braking resistor has overheated. 22350 Waiting to Run Closed: b1-11 Timer is active. 22351 Sequence timer 1 Closed: Sequence timer 1 is active. 22352 Sequence timer 2 Closed: Sequence timer 2 is active. 22353 Sequence timer 3 Closed: Sequence timer 3 is active. 22354 Sequence timer 4 Closed: Sequence timer 4 is active. 22358 Underload detection Closed: Underload is detected. 22360 Internal cooling fan alarm Closed: Internal cooling fan alarm 22471 Secondary PI Feedback Low Closed: PI2 feedback level is too low. 22472 Secondary PI Feedback High Closed: The PI2 feedback level is too high. 22489<1> Output I Lim Closed: Drive output speed is being limited due to the output current limit or due the single-phasefoldback regulator. 224100 to 189 Function 0 to 89 with inverseoutputInverts the output switching of the multi-function output functions.Set the last two digits of 1oo to reverse the output signal of that specific function. 224<1> Available in drive software versions PRG: 8503 and later.u H3: Multi-Function Analog InputsNo.(Addr.Hex) Name Description Values PageH3-01(410) Terminal A1 Signal LevelSelection0: 0 to 10 V1: -10 to 10 V2: 4 to 20 mA3: 0 to 20 mANote: Use Jumper S1 to set input terminal A1 for a current or voltageinput signal.Default: 0Range: 0 to 3 225H3-02(434) Terminal A1 FunctionSelection Sets the function of terminal A1. Default: 0Range: 0 to 26 225B.8 H Parameters: Multi-Function Terminals458 YASKAWA SIEP YAIP1U 01C AC Drive - P1000 Technical Manual
