Chapter 1414-26following:Book ModeA: COPIER>ADJUST>ADJ-XY>ADJ-XB: COPIER>ADJUST>ADJ-XY>ADJ-YF-14-54Feeder ModeC: COPIER>ADJUST>ADJ-Y-DFF-14-559) Execute the following in service mode to generate a service label;FUNCTION>MISCP> LBL-PRNT. Store the service label in theservice book case.14.3.4 When Replacing the Standard White Plate0008-3974iR105i/iR105+ / iR90701) Check to be sure that the Execute/Memory lamp in the control panelis OFF, and turn off the main power switch.2) Disconnect the power plug from the power outlet.The machine remains powered as long as its power plug is connected.Be sure to disconnect the power plug from the power outlet.3) Replace the standard white plate.4) Assemble the machine, and connect the power plug; then, turn on themain power switch.5) Execute the following in service mode in sequence:COPIER> FUNCTION> CCD> CCD-ADJCOPIER> FUNCTION> CCD> LUT-ADJ6) Inplement the service mode described below to the service sheetwhich is to be kept in the service log book case.COPIER> FUNCTION> MISC-P> LBL-PRNT7) Turn off and then on the main power switch.14.3.5 When Replacing the Standard White Plate0008-85961) Check to be sure that the Execute/Memory lamp in the control panelis OFF, and turn off the main power switch.2) Disconnect the power plug from the power outlet.The machine remains powered as long as its power plug is connected.Be sure to disconnect the power plug from the power outlet.3) Replace the standard white plate.4) Assemble the machine, and connect the power plug; then, turn on themain power switch.5) Execute the following in service mode in sequence:1. COPIER>FUNCTION>CCD>CCD-ADJ2. COPIER>FUNCTION>CCD>LUT-ADJ6) Inplement the service mode described below to the service sheetwhich is to be kept in the service log book case.- COPIER>FUNCTION>MISC-P>LBL-PRNT7) Turn off and then on the main power switch.14.3.6 When Replacing the Scanning Lamp0008-3976iR105i/iR105+ / iR90701) Check to make sure that the Execute/Memory lamp in the controlpanel is OFF, and turn off the main power switch.2) Disconnect the power plug from the power outlet.The machine remains powered as long a the power plug is connected. Besure to disconnect the power plug from the power outlet without fail.3) Replace the scanning lamp.4) Assemble the machine, and connector the power plug to the poweroutlet; then, turn on the main power switch.5) Execute the following in service mode in sequence:COPIER> FUNCTION> CCD> CCD-ADJCOPIER> FUNCTION> CCD> LUT-ADJ6) Inplement the service mode described below to the service sheetwhich is to be kept in the service log book case.COPIER> FUNCTION> MISC-P> LBL-PRNT7) Turn off and then on the main power switch.14.3.7 When Replacing the Scanning Lamp0008-85811) Check to make sure that the Execute/Memory lamp in the controlpanel is OFF, and turn off the main power switch.2) Disconnect the power plug from the power outlet.The machine remains powered as long a the power plug is connected. Besure to disconnect the power plug from the power outlet without fail.3) Replace the scanning lamp.4) Assemble the machine, and connector the power plug to the poweroutlet; then, turn on the main power switch.5) Execute the following in service mode in sequence:1. COPIER>FUNCTION>CCD>CCD-ADJ2. COPIER>FUNCTION>CCD>LUT-ADJ6) Inplement the service mode described below to the service sheetwhich is to be kept in the service log book case.- COPIER>FUNCTION>MISC-P>LBL-PRNT7) Turn off and then on the main power switch.14.3.8 After Replacing the Scanning Lamp0008-8583/ iR8070Execute'CCD auto adjustment'in service mode, and record the updatedCCD adjustmentdata on the service label.1. CCD Auto AdjustmentCOPIER>FUNCTION>CCD>CCD-ADJ2. CCD Adjustment Data all items underCOPIER>ADJUST>CCDBAC
