Chapter 1414-2714.3.9 Points to Note When Replacing the readercontroller PCB0008-3977iR105i/iR105+ / iR90701) Execute the following two items in service mode to print out settingsstored under items: COPIER> FUNCTION> MISC-P> LBL-PRNTand COPIER> FUNCTION> MISCP> USER-PRT.2) Check to make sure that the Execute/Memory lamp in the controlpanel is OFF, and turn off the main power switch.3) Disconnect the power plug from the power outlet.The machine remains powered as long as the power plug is connected.Be sure to disconnect the power plug from the wall outlet.4) Replace the reader controller PCB.5) Assemble the machine, and connect the power plug to the poweroutlet; then, turn on the main power switch.6) Execute the following in service mode: COPIER> FUNCTION>CLEAR> R-CON.7) Turn off and then on the main power switch.8) Execute the following in service mode: COPIER> FUNCTION>CCD> CCD-ADJ.9) Enter the settings printed out in step 1) for the following:- service modeCOPIER> ADJUST> ADJ-XY (4 items)COPIER> ADJUST> LAMP (1 item)COPIER> ADJUST> CCD (29 items)- user mode10) Turn off and then on the main power switch, and execute thefollowing in service modeto generate a service label; keep the service label in the service bookcase: COPIER> FUNCTION> MISC-P> LBL-PRNT.14.3.10 When Replacing the Reader Controller PCB0008-84491) Execute the following in service mode to generate the setting of eachitem: COPIER, FUNCTION>MISC-P>LBL-PRNT andCOPIER>FUNCTION>MISC-P>USER-PRT.2) Check to make sure that that Execute/Memory lamp in the controlpanel are OFF, and turn off the main power switch.3) Disconnect the power plug from the power outlet.The machine remains supplied with power as long as its power plug isconnected to a power outlet even when its main power switch is turnedoff. Be sure to disconnect the power plug.4) Replace the reader controller PCB.5) After assembling the machine, connect the power plug to the poweroutlet, and turn on the main power switch.6) Execute the following in service mode:COPIER>FUNCTION>CLEAR>R-CON.7) Turn on and then off the main power switch.8) Execute the following in service mode:COPIER>FUNCTION>CCD>CCD-ADJ.9) Enter the setting of each item generated in step 1):- Service ModeCOPIER>ADJUST>ADJ-XY (4 items)COPIER>ADJUST>LAMP (1 item)COPIER>ADJUST>CCD (29 items)- User Mode10) Turn off and then on the main power switch, and executeCOPIER>FUNCTION>MISC-P>LBL-PRNT in service mode togenerate a service label. Then, store it in the service book case.14.3.11 When Replacing the Reder controller PCB0008-8451/ iR80701) Print out the data of user mode/service mode.2) Check to make sure that the Execute/Memory lamp in the controlpanel ore OFF, and turn off the main power switch.3) Disconnect the power plug from the power outlet.The machine remains supplied with power as long as its power plug isconnected to a power outlet even when is main power switch is turnedoff.Be sure to disconnect the power plug.4) Replace the reader controller PCB.5) Remove the EEPROM (1 pc.) from the existing PCB, and mount it tothe new PCB.6) After assembling the machine, connect the power plug to the poweroutlet, and turn on the main power switch.7) Check to make sure that the following service mode settings are thesame as the data before replacement:COPIER>ADJUST>AE>all itemsCOPIER>ADJUST>ADJ-XY>all itemsCOPIER>ADJUST>CCD>all itemsIf any service mode setting is faulty, enter the respective settingrecorded on the service label in service mode.
