Chapter 1616-116.1 Error Code Table16.1.1 Outline0007-1248iR105i/iR105+ / iR9070 / iR8070The CPU on the machine's main controller PCB and DC controller PCB is equipped with a self diagnostic mechanism that monitors the condition of themachine (especially of the sensors); upon detection of a fault, it indicates the fact in the control panel using an error code.A description of each code and the timing of its detection are as discussed hereafter; the suffix that may follow each code is a detail code, which may bechecked in service mode (COPIER>DISPLAY>JAM/ERR).The error codes are grouped as follows according to the items they refer to:E000 to E399 error code related to the copierE400 to E499 error code related to the ADFE500 to E514 error code related to the finisherE515 error code related to the inserterE518 error code related to the paper folding unitE530 to E595 error code related to the finisherE5F0 to E5F9 error code related to the saddle stitch assemblyE601 to E830 error code related to the copierWhen the self diagnostic mechanism has gone ON, the machine may be reset by turning its power switch. This, however, does not apply to E000, E001,E002, E003, E004, E005, E013, E020, E717 or E719, indicating a fault which can lead to serious consequences if the machine is reset without removingthe cause (i.e., melting thermistor, which will overheat the fixing roller, or overflowing of toner from the hoper).If the code is from E000 to E003, the power switch will go OFF in about 30 sec if it is turned ON without resetting; in the case of E004, the power switchwill go OFF in about 3 sec after indicting E000 if the power switch is turned ON without resetting.You will have to clear the data in the RAM on the DC controller PCB for the following: E000, E001, E002, E003, E004, E005, E013, E020, E717 andE719.1) Execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.2) Press the Reset key twice to return to the Copy Mode screen.3) Turn off and the on the main power switch.16.1.2 Outline0008-9145iR85+The CPU on the machine's main controller PCB and DC controller PCB is equipped with a self diagnostic mechanism that monitors the condition of themachine (especially of the sensors); upon detection of a fault, it indicates the fact in the control panel using an error code.A description of each code and the timing of its detection are as discussed hereafter; the suffix that may follow each code is a detail code, which may bechecked in service mode (COPIER>DISPLAY>JAM/ERR).The error codes are grouped as follows according to the items they refer to:E000 to E399 error code related to the main bodyE500 to E514 error code related to the finisherE515 error code related to the inserterE518 error code related to the paper folding unitE530 to E595 error code related to the finisherE5F0 to E5F9 error code related to the saddle stitch assemblyE601 to E830 error code related to the main bodyWhen the self diagnostic mechanism has gone ON, the machine may be reset by turning its power switch. This, however, does not apply to E000, E001,E002, E003, E004, E005, E013, E020, E717 or E719, indicating a fault which can lead to serious consequences if the machine is reset without removingthe cause (i.e., melting thermistor, which will overheat the fixing roller, or overflowing of toner from the hoper).If the code is from E000 to E003, the power switch will go OFF in about 30 sec if it is turned ON without resetting; in the case of E004, the power switchwill go OFF in about 3 sec after indicting E000 if the power switch is turned ON without resetting.You will have to clear the data in the RAM on the DC controller PCB for the following: E000, E001, E002, E003, E004, E005, E013, E020, E717 andE719.1) Execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.2) Press the Reset key twice to return to the standby screen.3) Turn off and the on the main power switch.16.1.3 Error Code List0008-5846iR105i/iR105+ / iR9070
