06/15 Rev. 10 USER + SERVICE MANUAL /Status Reports64-xx – DPM – PEM – ALX 73x (PMA) – LPA 81x (Printer) – ALX 92x – AP 5.4 – AP 5.631529 Invalid Prn Mode ......................... 311530 Inc free str mem .......................... 311531 Inc RAM disc ............................... 311532 No Fixfont .................................... 311533 No Speedo Font .......................... 321534 ^XA missing ................................. 321535 ^XZ missing ................................. 322000-2009 Messages caused by Easy-Plug variables .............................. 322000 Double var name ......................... 322002 Var. data length ........................... 322003 Expr. bracket ............................... 322004 Exp. quotemark ........................... 322005 Exp. comma pos.......................... 322006 Exp.functionname........................ 322007 Exp.fct.paratype .......................... 332008 Exp.fct.paraCnt............................ 332009 Exp. name wrong ........................ 332010 Fct. para value............................. 332011 OLV variable................................ 332111 Invalid Date ................................. 332500 Multiple texts ............................... 343000/3003/3006/3012/3015Com x Overrun .................. 343001/3004/3007/3013/3016Com x Parity .................. 343002/3005/3008/3015/3017Com x Frame .................. 343010 Spooler Overflow ......................... 343011 Send buffer full ............................ 344100-4106 Message, which can onlyoccur with OLV-Option ................ 354100 No OLV data................................ 354101 OLV limit exceed ......................... 354103 OLV barcode type ....................... 354104 OLV Timeout ............................... 354105 No OLV response ........................ 364106 OLV Software .............................. 365000 Bus device ................................... 365001 No gap found ............................... 385002 Material end................................. 385003 Cover open .................................. 385004 Rewinder mat. tear ...................... 395005 Knife-fault .................................... 395006 Head-fault .................................... 395008 Ribbon end...................................395009 USI start error ..............................405012 Delete H8 loader ..........................405013 Prog H8 loader .............................405014 Power ...........................................405015 Scanner........................................415016 ALX Rewinder ..............................415017 Power Supply ...............................415018 Dot check area .............................425020 I2C Timeout xx .............................425021 I2C Conf. xx .................................425022 I2C Busy xx ..................................425023 I2C LAB xx ...................................425024 I2C BER xx ..................................425025 I2C Polling xx ...............................425026 Motorprotect CPU ........................435028 PS overheat .................................435029 I2C checksum xx..........................435051-5058 Messages which can onlyoccur with a TT4 printer ...............445051 Barcode Infeed 1..........................445052 Barcode Infeed 2..........................445053 Barcode Infeed 3..........................445054 Barcode Infeed 4..........................445055 Infeed 1 empty .............................445056 Infeed 2 empty .............................445057 Infeed 3 empty .............................455058 Infeed 4 empty .............................455059 Stacker full ...................................455060 Stacker full ...................................455061 Dispenser motor...........................465062 Disp. lift motor ..............................465063 Press roll ......................................465063 Lever open ...................................465064 Backing paper ..............................465071 Material end unw..........................465072 Material end unw..........................475100 No H8 response ...........................475100 Printengine lock ...........................475101 Headadjust error ..........................475102 Dot Defective ...............................475110 Foil low .........................................485120 Home position ..............................485121 Touch down .................................485122 PLC not ready ..............................48
