123Functions Used As NeededSet Mode4 Turn O to select [1 DW TIME].5 Press H.6 Turn O to select the monitoring interval.Interval can be selected from 0.1 SEC to 10 SEC.Remark Default: 5 seconds7 Press p to save the priority memory channel monitoringinterval setting and exit the Set mode.Turning illumination off when scanning stopsSCAN LAMP FunctionYou can set the backlight of LCD to turn ON or OFF when a signal is received duringscanning.Enter the Set mode:1 Press and hold M for over 1 second.2 Turn O to select [5 SCAN].3 Press H.4 Turn O to select [2 SCAN LAMP].5 Press H.6 Turn O to select [OFF].ON: The LCD backlight will light when a signal is received.OFF: The LCD backlight will not light when a signal isreceived.Remark Default: ON7 Press p to save the backlight ON or OFF setting whenscanning stops, and exit the Set mode.Setting the time to resume scanSCAN RE-START FunctionYou can set the time to resume scanning after a signal is received during scanning.Enter the Set mode:1 Press and hold M for over 1 second.2 Turn O to select [5 SCAN].3 Press H.䎔 䎃 䎧 䎺 䎃䎧 䎺 䎃 䎃䎷 䎬 䎰䎨䎃 䎃 䎃 䎃 䎃 䎘 䎑 䎓 䏖 䏈 䏆䏖 䏈 䏆䎃䎶 䎨 䎷 䎝 䎃 䎃 䎘 䎃 䎶 䎦 䎤 䎱䎃 䎃 䎃 䎃 䎃 䎃 䎃 䎃䎙 䎃 䎪 䎰䎃 䎃 䎃 䎃 䎃 䎃 䫹䎚 䎃 䎺 䎬 䎵 䎨 䎶 䙵 䎻䎃 䎃 䎃 䎃 䎃 䎃 䎃 䎃䎛 䎃 䎦䎲䎱 䎩 䎬 䎪䎔 䎃 䎧 䎺 䎃䎧 䎺 䎃 䎃䎷 䎬 䎰䎨䎕 䎃 䎶 䎦 䎤 䎱 䎃䎶 䎦 䎤 䎱 䎃 䎃䎯 䎤 䎰 䎳䎤 䎰 䎳䎃䎖 䎃 䎶 䎦 䎤 䎱 䎃䎶 䎦 䎤 䎱 䎃 䎃䎵 䎨 䙵 䎶 䎷 䎤 䎵 䎷䎃 䎗 䎃 䎶 䎦 䎤 䎱 䎃䎶 䎦 䎤 䎱 䎃 䎃䎵 䎨 䎶 䎸 䎰 䎨䎨 䎶 䎸 䎰 䎨䎖 䎃 䎶 䎦 䎤 䎱 䎃 䎃䎵 䎨 䙵 䎶 䎷 䎤 䎵 䎷䎗 䎃 䎶 䎦 䎤 䎱 䎃 䎃䎵 䎨 䎶 䎸 䎰 䎨䎃䎘 䎃 䎶 䎦 䎤 䎱 䎃 䎃䎺 䎬 䎧 䎷 䎫䎃 䎔 䎃 䎧 䎺 䎃 䎃䎷 䎬 䎰 䎨䎶 䎨 䎷 䎝 䎃 䎃 䎘䎶 䎨 䎷 䎝 䎃 䎃 䎘 䎃 䎶 䎦 䎤 䎱䎃 䎃 䎃 䎃 䎃 䎃 䎃䎃 䎃 䎃 䎃 䎃 䎃 䎃 䎃䎙 䎃 䎪 䎰䎃 䎃 䎃 䎃 䎃 䎃䎃 䎃 䎃 䎃 䎃 䎃 䫹䎚 䎃 䎺 䎬 䎵 䎨 䎶 䙵 䎻䎃 䎃 䎃 䎃 䎃 䎃 䎃䎃 䎃 䎃 䎃 䎃 䎃 䎃 䎃䎛 䎃 䎦䎲䎱 䎩 䎬 䎪