Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Overview of this manual
- Product documentation
- How to read the product manual
- Safety
- Protective stop and emergency stop
- Safety actions
- Emergency release of the robot axes
- Make sure that the main power has been switched off
- Safety risks
- Moving robots are potentially lethal
- First test run may cause injury or damage
- Work inside the working range of the robot
- Enabling device and hold-to-run functionality
- Risks associated with live electric parts
- The unit is sensitive to ESD
- Hot parts may cause burns
- Safety risks related to pneumatic/hydraulic systems
- Brake testing
- Safety risks during handling of batteries
- Safety risks during work with gearbox lubricants (oil or grease)
- Safety signals and symbols
- Safety symbols on product labels
- Installation and commissioning
- Unpacking
- Working range
- Risk of tipping/stability
- On-site installation
- Lifting and turning a suspended mounted robot
- Manually releasing the brakes
- Orienting and securing the robot
- Setting the system parameters for a suspended or tilted robot
- Loads fitted to the robot, stopping time and braking distances
- Fitting equipment on the robot (robot dimensions)
- Installation of signal lamp for 1600 (option)
- Installation of signal lamp for 1600ID/1660ID (option)
- Installation of the wire feeder shelf for 1600ID/1660ID
- Restricting the working range
- Installation of additional mechanical stops on axis 1
- Installation of additional mechanical stop on axis 2
- Installation of additional mechanical stops on axis 3
- Installation of position switch, axis 1
- Electrical connections
- Robot cabling and connection points
- Customer connections on the robot
- Start of robot in cold environments
- Maintenance
- Maintenance schedule and expected component life
- Maintenance schedule
- Expected component life
- Inspection activities
- Inspecting information labels
- Replacement activities
- Changing the oil in axes 5 and 6 gearboxes
- Changing the oil in axes 5 and axis 5 and 6 gearboxes, IRB 1600ID/1660ID
- Replacing the battery pack
- Cleaning activities
- Repair
- General procedures
- Mounting instructions for bearings
- Mounting instructions for seals
- Cut the paint or surface on the robot before replacing parts
- The brake release buttons may be jammed after service work
- Complete manipulator
- Replacing the cable harness, 1600ID/1660ID
- Replacement of complete arm system
- Upper and lower arm
- Replacing the complete upper arm, IRB 1600ID/1660ID
- Replacing the complete lower arm
- Replacing the wrist unit, IRB 1600
- Replacing the wrist unit, IRB 1600ID
- Replacing the wrist unit, IRB1660ID
- Replacing the damper, axis 2
- Replacing the damper, axis 3
- Replacing the mechanical stop axis 3, IRB 1600ID/1660ID
- Replacement of damper, axis 5
- Remove upper arm AW Gun
- Measuring the play 1600ID/1660ID, axis 5
- Measuring the play 1600ID/1660ID, axis 6
- Frame and base
- Replacing the serial measurement unit
- Replacing the push button unit
- Motors
- Replacement of motor, axis 2
- Replacement of motor, axis 3, IRB 1600
- Replacement of motor, axis 3, 1600ID/1660ID
- Replacement of motor, axis 4, IRB 1600
- Replacement of motor, axis 4, 1600ID/1660ID
- Replacement of motor and timing belt, axis 5, IRB 1600
- Replacement of motor, axis 5, IRB 1600ID
- Replacement of motor, axis 5, IRB 1660ID
- Replacement of motor and timing belt, axis 6, IRB 1600
- Replacement of motor, axis 6, IRB 1600ID
- Replacement of motor, axis 6, IRB 1660ID
- Gearboxes
- Service work on gearboxes, axes 3, 4, 5 and 6
- Calibration
- Calibration methods
- When to calibrate
- Synchronization marks and axis movement directions
- Calibration movement directions for all axes
- Updating revolution counters
- Calibrating with Axis Calibration method
- Calibration tools for Axis Calibration
- Installation locations for the calibration tools
- Axis Calibration - Running the calibration procedure
- Calibrating with Calibration Pendulum method
- Verifying the calibration
- Checking the synchronization position
- Decommissioning
- Scrapping of robot
- Robot description
- Type A of IRB 1600ID
- Reference information
- Applicable standards
- Unit conversion
- Screw joints
- Weight specifications
- Standard tools
- Special tools
- Lifting accessories and lifting instructions
- Spare part lists
- Circuit diagram
- Index
|
5.4 Calibrating with Axis Calibration method5.4.1 Description of Axis CalibrationInstructions for Axis Calibration procedure given on the FlexPendantThe actual instructions of how to perform the calibration procedure and what todo at each step is given on the FlexPendant. You will be guided through thecalibration procedure, step by step.This manual contains a brief description of the method, additional information tothe information given on the FlexPendant, article number for the tools and imagesof where to fit the calibration tools on the robot.Overview of the Axis Calibration procedureThe Axis Calibration procedure applies to all axes, and is performed on one axisat the time. The robot axes are both manually and automatically moved into position,as instructed on the FlexPendant.A fixed calibration pin/bushing is installed on each robot axis at delivery.The Axis Calibration procedure described roughly:• A removable calibration tool is inserted by the operator into a calibrationbushing on the axis chosen for calibration, according to instructions on theFlexPendant.WARNINGCalibrating the robot with Axis Calibration requires special calibration toolsfrom ABB. Using other pins in the calibration bushings may cause severedamage to the robot and/or personnel.WARNINGThe calibration tool must be fully inserted into the calibration bushing, untilthe steel spring ring snaps into place.• During the calibration procedure, RobotWare moves the robot axis chosenfor calibration so that the calibration tools get into contact. RobotWare recordsvalues of the axis position and repeats the coming-in-contact procedureseveral times to get an exact value of the axis position.WARNINGRisk of pinching! The contact force for large robots can be up to 150 kg.Keep a safe distance to the robot.• The axis position is stored in RobotWare with an active choice from theoperator.Continues on next pageProduct manual - IRB 1600/1660 3493HAC026660-001 Revision: W© Copyright 2006-2018 ABB. All rights reserved.5 Calibration5.4.1 Description of Axis Calibration
|
