5 -84Note Attach a Momentary Power Interruption Compensation Unit if compensation for power interruptions of up to 2.0 seconds is required for 200 V ClassInverters with outputs of 0.4 to 11 kW.* 1. The factory settings when VT is selected are given.When CT is selected, the factory settings are as follows for Inverters of any capacity:Carrier frequency selection: 1 (2.0 kHz)Carrier frequency selection upper limit: 2.5 kHz* 2. The setting of C6-02 changes the carrier frequency selection as follows:0: Low-noise PWM, 1: 2.0 kHz, 2: 5.0 kHz, 3: 8.0 kHz, 4: 10.0 kHz, 5: 12.5 kHz, 6: 15.0 kHz* 3. 95 for Inverter SPEC Type A.* 4. When setting the carrier frequency of 200 V Class Inverters of 30 kW or more to a value larger than the factory setting, reduce the value of the Inverterrated output current.Con-stantNumberName Unit Factory Setting- Inverter Capacity kW 18.5 22 30 37 45 55 75 90 110o2-04 kVA selection - 9 A B C D E F 10 11b8-03 Energy-saving filter timeconstant s 0.50 (Open loop vector control) 2.00 (Open loop vector control)b8-04 Energy-saving coeffi-cient - 57.87 51.79 46.27 38.16 35.78 31.35 23.10 20.65 18.12C6-01 CT/VT selection - 1 1 1 1 1 1 1 1 10 0 0 0 0 0 0 0C6-02Carrier frequency selec-tion (when VT isselected) *1 *4- 6 *2 6*2 4 *2 3 *2 3 *2 3 *2 2 *2 2 *2 1 *2-Carrier frequency selec-tion upper limit (whenVT is selected)*1- 6 6 6 4 4 4 4 4 1E2-01(E4-01) Motor rated current A 65.8 77.2 105.0 131.0 160.0 190.0 260.0 260.0 260.0E2-02(E4-02) Motor rated slip Hz 1.67 1.70 1.80 1.33 1.60 1.43 1.39 1.39 1.39E2-03(E4-03) Motor no-load current A 15.7 18.5 21.9 38.2 44.0 45.6 72.0 72.0 72.0E2-05(E4-05)Motor line-to-line resis-tance Ω 0.101 0.079 0.064 0.039 0.030 0.022 0.023 0.023 0.023E2-06(E4-06) Motor leak inductance % 20.1 19.5 20.8 18.8 20.2 20.5 20.0 20.0 20.0E2-10 Motor iron loss fortorque compensation W 505 538 699 823 852 960 1200 1200 1200L2-02 Momentary power lossridethru time s 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0L2-03 Min. baseblock (BB)time s 1.0 1.0 1.1 1.1 1.2 1.2 1.3 1.5 1.7L2-04 Voltage recovery time s 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0L2-08 Frequency reductiongain at KEB start °C 95 95 95 95 95 95 95 95 95L8-02 Overheat pre-alarm level °C 100 90 90 95 100 105 110 100 110 *3N5-02 Motor acceleration time s 0.317 0.355 0.323 0.320 0.387 0.317 0.533 0.592 0.646
