User Constants10- 3310E1-13 Base voltage 0.0 *11 F1-09 Overspeed detection delay time 0.0*7E2-01 Motor rated current 1.90*6 F1-10 Excessive speed deviation detec-tion level 10E2-02 Motor rated slip 2.90*6 F1-11 Excessive speed deviation detec-tion delay time 0.5E2-03 Motor no-load current 1.20*6 F1-12 Number of PG gear teeth 1 0E2-04 Number of motor poles 4 F1-13 Number of PG gear teeth 2 0E2-05 Motor line-to-line resistance 9.842 *6 F1-14 PG open-circuit detection time 2.0E2-06 Motor leak inductance 18.2 *6 F2-01 Bi-polar or uni-polar input selec-tion 0E2-07 Motor iron saturation coefficient 1 0.50 F3-01 Digital input option 0E2-08 Motor iron saturation coefficient 2 0.75 F4-01 Channel 1 monitor selection 2E2-09 Motor mechanical loss 0.0 F4-02 Channel 1 gain 1.00E2-10 Motor iron loss for torque compen-sation 14*6 F4-03 Channel 2 monitor selection 3E2-11 Motor rated output 0.40*6 F4-04 Channel 2 gain 0.50E3-01 Motor 2 control method selection 0 F4-05 Channel 1 output monitor bias 0.0E3-02 Motor 2 max. output frequency(FMAX) 60.0 F4-06 Channel 2 output monitor bias 0.0E3-03 Motor 2 max. voltage (VMAX) 200.0 *2 F4-07 Analog output signal level forchannel 1 0E3-04 Motor 2 max. voltage frequency(FA) 60.0 F4-08 Analog output signal level forchannel 2 0E3-05 Motor 2 mid. output frequency 1(FB) 3.0 *2 F5-01 Channel 1 output selection 0E3-06 Motor 2 mid. output frequencyvoltage 1 (VC) 15.0 *9 F5-02 Channel 2 output selection 1E3-07 Motor 2 min. output frequency(FMIN) 1.5 *2 F5-03 Channel 3 output selection 2E3-08 Motor 2 min. output frequencyvoltage (VMIN) 9.0 *9 F5-04 Channel 4 output selection 4E4-01 Motor 2 rated current 1.90 *6 F5-05 Channel 5 output selection 6E4-02 Motor 2 rated slip 2.90 *6 F5-06 Channel 6 output selection 37E4-03 Motor 2 no-load current 1.20 *6 F5-07 Channel 7 output selection 0FE4-04 Motor 2 number of poles (numberof poles) 4 F5-08 Channel 8 output selection 0FE4-05 Motor 2 line-to-line resistance 9.842*6 F5-09 DO-08 output mode selection 0E4-06 Motor 2 leak inductance 18.2 *6 F6-01 Operation selection after commu-nications error 1E4-07 Motor 2 rated capacity 0.40*6 F6-02 Input level of external fault fromCommunications Option Board 0F1-01 PG constant 600 F6-03Stopping method for external faultfrom Communications OptionBoard1F1-02 Operation selection at PG open cir-cuit (PGO) 1 F6-04 Trace sampling from Communica-tions Option Board 0F1-03 Operation selection at overspeed(OS) 1 F6-06 Torque reference/torque limitselection from optical option 0F1-04 Operation selection at deviation 3 F6-08 Operation selection after SI-TWDT error 1F1-05 PG rotation 0 F6-09 Number of SI-T BUS error detec-tion 2F1-06 PG division rate (PG pulse moni-tor) 1 H1-01 Terminal S3 function selection 24F1-07 Integral value during accel/decelenable/disable 0 H1-02 Terminal S4 function selection 14F1-08 Overspeed detection level 115 H1-03 Terminal S5 function selection 3 (0) *12Table 10.7 User Constants (Continued)No. NameFac-torySettingSet-ting No. NameFac-torySettingSet-ting
