Kenwood TK-3180 Function Reference

Also see for TK-2180: Specifications Brochure & specs Instruction manual Instruction manual Service manual

Contents

21 2-TONE92 Function Reference Version: 1.11! Alert ToneYou can configure the Alert Tone to transmit when thetransceiver receives a call using 2-tone signaling.You can select one of eight tone patterns configured inthe Alert Tone Pattern. (Refer to 4.7 Alert Tone Pattern.)! Configuration using KPG-89D• Configuring the Call Format (Refer to FPRG6.10.2 Decode tab - Call Format.)• Configuring the Transpond function (Refer toFPRG 6.11.2 Decode tab - Transpond.)• Configuring the Alert Tone (Refer to FPRG 6.11.2Decode tab - Alert Tone.)21.3.2 A Tone/ B Tone/ C Tone/D ToneThis function allows you to configure the frequency of thetones. You can configure the frequency between 288.5and 3106.0 Hz.! Configuration using KPG-89D• Configuring the A Tone/ B Tone/ C Tone/ D Tone(Refer to FPRG 6.11.2 Decode tab - A Tone/ BTone/ C Tone/ D Tone.)21.3.3 Auto Reset TimerThe Auto Reset Timer is the duration from the time whencommunication ends to the time when the 2-tone matchstatus is reset.You can configure the Auto Reset Timer using KPG-89D.You can also configure the operation after the Auto ResetTimer is expired.Table 21-4 Operation after the Auto Reset Timer is expired.! Configuration using KPG-89D• Configuring the Auto Reset Timer (Refer to FPRG6.11.2 Decode tab - Auto Reset Timer.)• Configuring the LED (Refer to FPRG 6.11.2Decode tab - LED.)• Configuring the Alert (Refer to FPRG 6.11.2Decode tab - Alert)• Configuring the Monitor function (Refer to FPRG6.11.2 Decode tab - Monitor.)21.3.4 Clear to TranspondThis function prevents the transceiver from performingthe Transpond function until the channel becomesavailable.You can enable/disable the Clear to Transpond functionusing KPG-89D.! Configuration using KPG-89D• Configuring the Clear to Transpond (Refer toFPRG 6.11.2 Decode tab - Clear to Transpond.)21.3.5 Selective Call Alert LEDThis function makes the SelCall Alert LED blink when thecode is received.You can enable/disable the Selective Call Alert LED usingKPG-89D. (Refer to 22.2 Selective Call Function.)Note:" The match status of 2-tone resets in the following conditions.Table 21-5 Condition to reset the 2-tone Match StatusYes Off The transceiver transmits theTranspond Tone.No Other thanOffThe transceiver transmits the AlertTone.Yes Other thanOffThe transceiver transmits the AlertTone after it transmits theTranspond tone.Auto Reset Timer OperationOff The Auto Reset Timer does not work.LED indicatorThe orange Selective Call Alert LEDstops blinking when the Auto ResetTimer expires.AlertThe intermittent transmission of the AlertTone stops when the Auto Reset Timerexpires.Transpond Alert OperationMonitor The match status of the DTMF resetswhen the Auto Reset Timer expires.Operation ConditionPress a key.One of the following keys is pressed.• PF Monitor key• PF Monitor Momentary key• PF Squelch Off key• PF Squelch Off Momentary key• PF Zone Up key• PF Zone Down key• PF Zone Up/Down key• PF CH/GID Up key• PF CH/GID Down key• PF CH/GID Up/Down key• PF Scan key• PF Home CH/GID key• PF Direct CH/GID 1 - PF Direct CH/GID 5keyOn-hook The microphone status becomes On-hook.Auto Reset Timer Operation