Version: 1.11 Function Reference 10522 FLEETSYNC! EmergencyWhen the transceiver receives the reserved statusmessage, the Alert or both of the Alert and Horn isactivated according to the Emergency StatusResponse configuration.! Remote StunThis function allows you to disable almost all thetransceiver’s functions. Only the following operationsfunction when the Stun function is enabled. Thetransceiver recovers from the Stun status whenreceiving the Stun Deactivation status message or theStatus Deactivation command by DTMF.Table 22-9 Status Message Output! Status 90 - 92These statuses allow you to command or reset the Stunfunction.This function operates regardless of the Stun status of thereceiving party's transceiver.! Status 93 - 94These statuses are used to respond to the Stun statusof the transceiver when receiving the RSTM (RequestStatus).22.3.4 Status Message StackThis function is used to store the received StatusMessage in the Stack memory. The transceiver can storea maximum of 15 Status Messages.When the message is stacked, the “ ” icon blinks. Inthis case, a user can read the stored Status Message byentering Stack Mode. (Refer to 22.7 Stack.)You can configure the Status Message to be stackedusing KPG-89D.Note: The transceiver can stack a maximum of 15 StatusMessages.! Configuration using KPG-89D• Configuring the Status Message Stack (Refer toFPRG 6.12.2 General 2 tab - Status MessageStack.)22.3.5 Status Message on Data Zone-CH/GIDThis function allows the transceiver to automaticallychange the Data Zone-CH/GID to send the StatusMessage.The transceiver automatically changes the channel toData Zone-CH/GID to transmit the Status Message. Thetransceiver returns to the previous Zone-CH/GID whenthe transmission ends. This function allows a user tosend data using the selected Zone-Channel/Group ID.You can enable/disable this function using KPG-89D.! Configuration using KPG-89D• Configuring the Status Message on Data Zone-CH/GID function (Refer to FPRG 6.12.3 Parametertab - Status Message on Data Zone-CH/GID.)22.3.6 Status Message Serial OutputThis function allows the transceiver to send the caller’sFleet/ID from the transceiver’s communication port whenthe transceiver receives a Status Message.The dispatcher can remote control the transceiver with aPC. It can also retrieve the transceiver’s statusinformation by connecting external devices.You can enable/disable this function using KPG-89D.! Configuration using KPG-89D• Configuring the Status Message Serial Output(Refer to FPRG 6.12.2 General 2 tab - StatusMessage Serial Output.)22.3.7 AUX Input Status MessageThis function allows the transceiver to send the StatusMessage when the status of the AUX IN terminalalternates to low from high.You can send the Status Message by connecting asensor to the AUX IN terminal. The transceiver sends thestatus message to the FleetSync ID configured in theTarget Fleet/ID (Status Message).*1 You can enable/disable the Status 80 - 99 when using the ManualDialing function with KPG-89D. (Refer to 22.3.13 Status 80 - 99(Special).)*2 The Horn Alert terminal does not activate when the Off-hookHorn Alert function is disabled and the microphone is in the Off-hook position.*3 In this case, the Stun Status does not change even if a userchanges the Status in Status Mode.*4 You can enable/disable the Status 80 - 99 when using the ManualDialing function with the KPG-89D. (Refer to 22.3.13 Status 80 -99 (Special).)Status Message Inhibit TX. Inhibit TX/RX.Normal Operation Inhibit TX. Inhibit TX/RX.PC ControlThe transceiver doesnot accept thetransmission request.It does not output thereceived data.The transceiver doesnot accept thetransmission request.It does not output thereceived data.