Kenwood TK-3180 Function Reference

Also see for TK-2180: Specifications Brochure & specs Instruction manual Instruction manual Service manual

Contents

Version: 1.11 Function Reference 4914 PTT IDThis is the identification code transmitted when the PTTswitch is pressed and/or released.By using this ID, the base station (dispatcher) can identifythe caller without asking for the caller’s name.You can configure the following items to PTT ID usingKPG-89D.• PTT ID Type• PTT ID (CH/GID Information)• Restricted ID in TA14.1 PTT ID TypeYou can select the PTT ID type. Select DTMF orFleetSync as the PTT ID format.You can select DTMF or FleetSync using KPG-89D.You can configure the Beginning of Transmit and the Endof Transmit when the DTMF is selected. (Refer to 14.1.1Beginning of Transmit, 14.1.2 End of Transmit.)You can configure the Fleet (Own) and the ID (Own)when selecting FleetSync. (Refer to 22.9.1 Own Fleet/ID.)! Configuration using KPG-89D• Configuring the PTT ID Type (Refer to FPRG6.7.3 Common-Page 3 tab - PTT ID Type.)14.1.1 Beginning of TransmitYou can configure the ID to be sent at the beginning oftransmit when the DTMF is selected.You can configure the ID to be sent as the BOT usingKPG-89D. No ID will be transmitted if you do notconfigure the BOT ID.! Configuration using KPG-89D• Configuring the Beginning of Transmit (Refer toFPRG 6.7.3 Common-Page 3 tab - Beginning ofTransmit.)14.1.2 End of TransmitYou can configure the ID to be sent at the beginning oftransmit when selecting DTMF.You can configure the ID to be sent as the EOT usingKPG-89D. No ID will be transmitted if you do notconfigure the content of the ID.! Configuration using KPG-89D• Configuring the End of Transmit (Refer to FPRG6.7.3 Common-Page 3 tab - End of Transmit.)14.2 PTT ID(CH/GID Information)PTT ID (CH/GID Information) allows you to select thetiming to send the PTT ID.You can enable/disable the PTT ID for each CH/GIDusing KPG-89D. The following configuration is available.Table 14-1 Timing to Transmit the PTT ID(When the PTT ID Type is DTMF/ANI board.)Table 14-2 Timing To Transmit the PTT ID(When the PTT ID Type is FleetSync.)Table 14-3 Timing to Transmit the PTT ID(When the PTT ID Type is ANI board.)Note:" “List 1 - 100” and “On” do not appear when selecting “DTMF”using the PTT ID pulldown menu." “On” will not appear when selecting “FleetSync” using the PTTID pulldown menu." “BOT”, “EOT”, “Both”, and “List 1 - 100” do not appear whenselecting “ANI Board” using the PTT ID pull-down menu.PTT ID Timing to Transmit the PTT IDOff No PTT ID is transmitted.BOT This PTT ID is transmitted each time thePTT switch is pressed.EOT This PTT ID is transmitted each time thePTT switch is released.Both This PTT ID is transmitted when the PTTswitch is pressed and released.PTT ID Timing To Transmit the PTT IDOff No PTT ID is transmitted.BOTFleet (Own) and ID (Own) are transmitted asthe PTT ID when the PTT switch or the PFExt. PTT (Voice) port is pressed.EOTFleet (Own) and ID (Own) are transmitted asthe PTT ID when the PTT switch or the PFExt. PTT (Voice) port is released.BothFleet (Own) and ID (Own) are transmitted asthe PTT ID when the PTT switch or the PFExt. PTT (Voice) port is pressed andreleased.List 1 - 100(FleetSync only)You can make an individual call. You canselect the ID from 1 to 100 in the SelCall list.You can make a SelCall using the Fleet andthe ID.PTT ID Timing To Transmit the PTT IDOff No PTT ID is transmitted.OnThis ANI code of the ANI Board is sent. Thetiming to transmit the PTT ID must beconfigured to the ANI board.